i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
I couldn't find nrf_drv_timer.c file. I want to create timer so I try to different SDK for my work. I am using SEGGER IDE for prepare software but i encountered lots of problems...
Dear nordic,
I try to build BLE application everything works fine expect the UART. The UART has transmission issue.
it has no problem in receiving. but when i tried...
Hi,
I am using nrfMesh2.2 SDK. I want to add models other than GenericOnOff and configurationclient to the interactive_pyaci. How do we proceed with this?
I found the utility to create the binary image of the production data for my Zigbee device but cannot find any documentation on how to incorporate the generated BIN file into...
Hi,
I have a custom board with nRF52832 and I'm using SDK 13.1 and softdevice s132 4.0.5. I have a GPRS module that I will use to receive the new firmware image and I will...
Dear Nordic,
I installed nrfConnect 2.6.1 and lauched "BluetoothLow Energy" application. Then i selected my board and it asked "Device must be programmed ..." and loaded...
Hi There,
I'm interested to customize the eddystone TLM parameters as per the image below, which is replace the Battery voltage with Button detection On/Off.
I did...
I was able to successfully make the BLE Peripheral Eddystone Beacon Application in "nRF5_SDK_12.3.0_d7731ad" in Windows 7 32-bit (pca10040), using GNU Tools ARM Embedded version...
Greetings,
I'm fairly new to developing with Nordic ICs using the SDK, I have previously developed for some nRF51x MCUs using some modules that had an Arduino library...
hello , everyone
platform : NRF52832, SDK13.0 , project:\examples\ble_peripheral\ble_app_template
I meet such a problem, config app_timer in APP_TIMER_MODE_REPEATED and...
Hi,
I cannot get the interrupt on Timer1 to work. I have checked that the counter is matching the compare register by not enabling the interrupt. When I enable the interrupt...
According to the official suggestion circuit, I’ve deleted some functions which are useless for me, (the schematic circuit diagram and PCB are showed in the end) then I use...
Hi all
I'm using nRF52 DK with 14.2.0 SDK. I created a LED blink project for testing and extract its HEX file. I uploaded the program to the nRF52 over USB (J-Link-Keil...
Hi Nordic:
I use the nrf Connect to upload a new zip , the dfu progress goes to 21%,and then I get a error.
Error msg:
DFU failed with error: When writing 'CREATE...
