We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Dear all,
I'm using NRF52832 with SDK 14.2.0 and SD 132 v5.0.0.
I have my own implemented application working properly when is flashed directly without bootloader, only...
Hi,
I'm wondering if anybody has performed a test of, or has experience with Nordic Semiconductor thread mesh stack (nRF5 SDK for Thread and Zigbee v1.0.0) in a large scale...
Hi, i used the 'nrf5_SDK_for_Mesh_v2.0.1_src\examples\light_switch' i have two question:
1: How to added more Client in one mesh net?
2: How to configuare node to 'low...
I am trying to make RF USB dongle using nrf52840.
Before the PCB production, we are using DK to test, but the firmware is not uploaded because VDDH and VBUS of DK are connected...
Hello Nordic!
Sometimes we have a problem with a services discovery. We have no custom services. Only DIS, BAS, NUS and DFU. (nRF52832 and SDK15)
This problem is currently...
Hi,
I'm working with the light_switch example on Mesh 2.0.1 and I would like to modify the simple_on_off_client_set_unreliable function to broadcast to all servers in the...
I am evaluating TAIYO YUDEN board EKSHSNZWZ.
I've flashed s132_nrf52_5.0.0_softdevice.hex using nRFgo Studio.
I use Keil uVision to test "nRF5_SDK_15.0.0_a53641a\examples...
Hi. I am trying to transmit a microphone signal to the nrf52832 DK board.
Before development, i checked it by connecting a microphone(ADC) and a speaker(PWM) to one...
It wasn't until I downloaded nRF-Sniffer-v2 that I discover the release note below that explicitly states that nrf_sniffer now supports all platforms supported by Wireshark...
Hi,
We want that any bulb or any devices (Server device) of BLE 4.2 should be able to work with BLE Mesh SDK(Client). We are using the nrf52832 with SDK BLE_2.0.1 for the...
I would like to sample a digital IO input from two IO's into the processor internal memory incrementally per every rising or falling edge of each of the signals.
Is there...
I was trying to follow with the steps in this link: https://github.com/NordicPlayground/Nordic-Thingy52-mesh-demo
I got an error in the first step while running the setup_sdk...
I have an issue with compilng and loadingthe nrf52840 examples.
I have a nrf52480 pdk and a keil v5 installed on windows.
Everything is ok when I compile and load nrf52840_xxAA...
Hi,
I am using nRF52840 DK which runs blood pressure example. With nRFcloud gateway and nrfcloud.com, I have connected successfully the development kit. Observed that RSSI...
