Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
I am using the nRF52832 (on Rigado BMD-300 EVAL kit). I am using keil IDE and nRF GO to upload my compiled code to my device. I am using SKD 15.2.0. Using Windows 10.
...
i donot know why,because other board is ok.
i am using this project
\nRF52832 pack\nRF5_SDK_14.2.0_17b948a\nRF5_SDK_14.2.0_17b948a\examples\ble_central\ble_app_uart_c...
I am migrating my project from SDK 15.0 to SDK 15.2. I was using CC310 to accelerate crypto in the bootloader.
While builiding the bootloader wit SDK 15.2, I got the error...
Hi team, Does the nordic chip receive a Bluetooth signal being communicated with a mouse, keyboard, cell phone, etc., and the sleep state (sd_app_evt_wait()) is canceled?...
Hi,
Can we use BLE 5 beacon with BLE 4 scanner?
As BLE 5 is long range which is my main concern. So, can I get that long range with BLE 4 scanner?
Thanks,
i have done the 10 dfu steps in DFU quick start guide when the boards are not far from each other it works but when i make them far a little
i mean one device in the area...
I am using a Sparkfun nRF52832 breakout. I was trying to install the Softdevice settings onto my Arduino IDE once I clicked on tools -> "nRF5 flash device " the blue ticking...
Current consumption of my code running RTC from LFCLK is ~2.5uA from the power profiler when I set the register values as. NRF_POWER->RAM[2].POWERCLR = 0x01; NRF_POWER->RAM...
Hi,
Currently evaluating SDK and have some issues, I would like to run some demos.
I believe I've managed to erase the "preconfigured" Firmware on the SDK, I have tried...
I am working on SDK-15.2, nRF52832 Dev board. My question is how to add write protected characteristic by KEY? Mean when we want to write something from peer device (smartphone...
1. I've noticed while using tools like NRFConnect that most BLE devices in my proximity do not include the device name in the advertising packet. My assumption is the developers...
Hello, I am unable to connect thingy 52 with my laptop, I have NRF connect v2.6.1 installed but it is unable to find thingy.
Thingy is not connected with any other device...
hello,
I am using the SDK15.2 for development.
I want to set a central address in peripheral like the whitelist function via uart without bonding.
This code is about...
Hello,
We are working with nrf52832 which have a custom application with SDK 13.1 and softdevice s132_nrf52_4.0.5_softdevice, we have migrated to sdk 15.2 s132_nrf52_6.1...
