But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hi i have problem i can flash via st-link but when i want program nrf52832 via bluetooth(smartphone). i create zip with bootloader, softdevice and app and that zip send to...
Affects nRF5 SDK v13.0.0 - v15.0.0
I noticed a minor bug in peer_manager.c, lines 972-975 (v15.0.0). Looks like an opening brace is on an incorrect line, see line 5 in...
I'd like to share a SPI bus between the nRF52840 and another IC. The chips are on different load switches, though, and I'd need to communicate over the SPI bus with my other...
Hi!
I'm New to BLE Mesh and i would like to implement Text Data Transfer and receive to multiple BLE's using Bluetooth Mesh on nRF52832, Can anyone suggest me how to get...
hi:
I am now using nrf52832 development bracelet, I have nRF52 DK and nRF6707,Using the latest version of PPK software testing,I am now ready to use PPK to test the power...
Hi Guys,
I'm doing the RF test based on nRF24le1, could you share any good antenna sample for this chip?
i found a TI 2.4g antenna design http://www.ti.com/lit/an/swra117d...
SEGGER EMBEDDED __align(4) have error info.I can use __align(4) normally, but there is a error information in SEGGER embedded
this error is "expected declaration specifiers...
Hi Nordic Devzone,
I'm working with nrf52-PDK and Mesh SDK, I wanted to know that if it is possible to send and receive some data at the same time?
And if I can do that...
I have made a custom board by following the reference design given in the nordic website using 2450BM14E0003 Balun and 2450AT18B100E chip antenna from Johannson technology...
HI,
My application is based on on your example ble_perepherical/ble_app_uart.
I realised few modification.
Now, after a BLE timeout, the circuit doesn't sleep anymore...
I am requesting timeslots with an interval of multiple seconds. But sometimes I want to switch to an interval of several milliseconds. How can I cancel the pending timeslot...
Using some of our nRF51 dongles as sniffers to debug BLE.
Sniffer software --> "w" --> Wireshark, no problems.
Post processing wireshark export *.csv files. No problems...
Hi.
Is there some code example for Bluetooth button for PTT aplication Zello ?
When I press a button BLE should send notify event =1, when released BLE send notify event...
I'm building battery power BLE mesh network the nodes mast have the publishing period match greater than 5 minutes. And my question is how to estimate the power consumption...