But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
When I study the ANT example, ANT Advanced Burst, in SDK document, I see this:
The transmission rate, along with optional features such as frequency hopping, is negotiated...
dear nordic employee
when I send the data with 131 length by function sd_ble_gatts_hvx
some times it return NRF_SUCCESS，but some times It return 19error
I cannot...
Hi.
I'm in the process of migrating an application from the nRF51822 and SDK 12.2.0 to the nRF52832 and SDK 13.0.0. My code now compiles but doesn't link. Here's the make...
Hi,
I tried using ble_notification interrupt to 'warn' me before the start of radio activity so that I can get around the CPU blocking issue. But, for some reason, for 1...
I am working on blinky example and want to modify service/characteristic uuid. I do
that in ble_lbs.h as follows:
//#define LBS_UUID_SERVICE 0x1523
#define LBS_UUID_SERVICE...
I had the following setup, two app_timers triggering blocking SAADC reads in the callback functions
app_timer 1000ms triggering 1 Blocking SAADC read (For battery service...
Hello,
I use sdk 8.0.0 and s110. I read this blog
And I did not understand some terms;
Application processing(for example 2ms each adv interval)
Number of packets...
Hi,
I am using the nRF51 Dongle (PCA10031, V 1.1.0) and pc_ble_driver.py to create a custom script for testing purposes. But there seems to be a maximum limit for the measured...
I met a problem when delete bonding information on android central, i actually can't connect to the nrf52832 peripheral again, until i totally clear it's peer list and bond...
Hi all,
I am trying to control a speaker using the i2s output of the nrf52832 mapped into a TAS2505 from TI. I am able to play sounds in the speaker but my issue is that...
I am trying to use the eddystone example I found in the ble_prepheral/ble_app_eddystone/pca10040 folder in SDK14.2 with my nRF52832 development board but I get the following...
i found this link on nordic website to learn ARM with Nordic SOC.
www.nordicsemi.com/.../Nordic-ARM-Lab-in-a-Box-University-Program
Do you know where is the link for...
Hi,
I am able to program a SparkFun nRF52 breakout board via nrf52 Dev Kit using Segger Embedded Studio. However, I am not able to achieve the same results using nrfjprog...
I am facing some issue while writing to i2c. On first i2c write , device is working but after that when i tries to write anything, code is stucking in loop.
void sensor_sleep_mode...
