But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello,
I want to use the PCA10040 to program a custom board running on 1.8V using the debug out port. Is this possible?
Also, is there a way to set up the PCA10040 so...
Device: nrf52, sd132 v3.0.0, SDK 12.1 (and also 12.3), freeRTOS, BLE peripheral, gcc-arm-none-eabi-5_4-2016q2
I am experiencing an issue which is causing our device to...
Hi everyone,
I am developing a remote control using nRF52832 chip. My prototype is currently developed in PC10040 board. The IDE is Eclipse Oxygen, and the SDK is S132...
Hi, now I'm using NRF52832 's UART with SD12 and it required to receive 40 bytes per 10ms.
In fact, it does not take 10ms to complete the reception.So my idea is to create...
Hello,
I'm working on a type of activity tracker using the NRF52, and I'm a bit stuck with time aspects.
The device stores two versions of activity data; daily totals...
Hi
First I wrote a post because the initialization was crashing, but now I found out it was because the RX line was low.
How to initialize the uart if the RX line is low...
hi i have a problem with ble app uart.i used nRF5_SDK_12.3.0_d7731ad and Eclipse Mars 2.
I had build main.c in hex ble_app_uart\pca10040\s132 . And after that a maked mergehex...
Hello,
I am trying to update our application with DFU support but it will not work for me. One of 2 things happens:
Programming the bootloader and softdevice by programming...
Hello,
We have the following setup:
SDK Version: nRF51_SDK_8.1.0
bootloader Version: dfu_dual_bank_ble_s110_pca10028.hex
soft Device: s110_nrf51_8.0.0_softdevice...
Hello,
I'm working on a concurrent role device (advertiser+scanner+peripheral+central) and devices are configured to connect each other in a mesh-like way (Note: I'm not...
Hi,
i am using ble_app_hrs_c_pca10056_s140 and when connected to one particular device i need to access it's GATT profile services and characteristics.In example ble_app_hrs_c_pca10056_s140...
Hi,
I am working with the nRF52832 development board and am running SDK 13.1.0 and SoftDevice 212 4.0.2. I have flashed a modified version of the broadcast example onto...
Hi everybody,
We have used both nrf51822 from batch 2015 week 33 and 2016 week 27 and found big discrepencies on BLE connections (stability issues)
Is there major differences...
