But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
I am having errors building the examples in the latest SDK for Mesh (nrf5_SDK_for_Mesh_v0.10.0-Alpha_src). I ran cmake -DTOOLCHAIN=gccarmemb -DPLATFORM=nrf52840_xxAA .. in...
Hello,
I'm using NRF52832 with SoftDevice S132, and SDK 14.0.0 to make NUS peripheral and central. To test it I have one NUS peripheral device, that echoes incoming data...
Using SDK 13 FDS, I store 6468 byte, that is 1617 words, including FDS header. Of course this size is total.
In detail in byte size, this size consists of
(12(header)...
Hi,
I'm wondering if the slave connection interval range is the same as the GAP peripheral preferred connection parameters i.e. does it make sense to do the following ...
Hello!
I'm developing thread application with COAP communication. I've got problem with message queue on router. Everything works fine when operating as a child. I have cyclic...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
Hi,
I'm trying to get started with the nRF51-DK with the ble_app_template. I want to get it working in the Rowley CrossWorks IDE. (From what I understand this is the same...
I am having trouble running softdevice_enable. Here is what happens:
After main(void) starts the code is:
log_init(); // WORKS
clock_init(); // WORKS
buttons_leds_init...
Hello,
I'm using a nRF51822 to send data to the iPhone using the NUS service. I'm using the oldest SDK4.x and v5.x S110 soft device. I know that the least connection interval...
Good day.
I`m very new to nordic chips.
I`m try to use NRF52832 as TWI master with OLED display based on SSD1306 with I2C.
And got this.
Yellow is SCL, Blue...
Hi,
I am trying to use the FDS for saving some variables and displaying them again later. I have downloaded the NRF52-fds-master sample code posted on github. However,...
i am working with mpu xx example given in nordic website. it seems code is working fine i.e. compiling and dumping into nrf52 DK, But not showing any output values.
i was...
I am using an Nrf51822 for a project. I looked in the datasheet and it said that there is a built in WDT for the chip. It also says that clocks can't be used while in systems...
I want to use in my project tft 1.8 display with st7735 controller. I'd like to use some based code but can find nothing except on infocenter nordic
As I understand there...
Hi,
I am writing a boot loader which does not need to use the soft device as the image is being transferred over an SPI interface.
I have merged the softdevice and my...
