This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
When I run an infinite loop of NOP on the NRF52DK, the led's remain dark. But when I run an infinite loop of:
nrf_gpio_cfg(
pin,
NRF_GPIO_PIN_DIR_INPUT,
NRF_GPIO_PIN_INPUT_DISCONNECT...
I have worked on the new project with nRF5_SDK_13.1.0_7ca7556. I have got an compiling error with app_timer.c. The error message is as below:
Building ‘app_timer.c’ from...
Hi all!
I'm doing some tests on throughput and power consumption on the nRF51822, using SoftDevice 130. I use an application that sends 20 bytes notifications from slave...
Hello, Nordic Forum!
I've been developing a wrapper library that uses the FDS to store my application data.
I have 3 type of data to store: an array of 14 uint16_t , an...
I've been banging my head against this for a couple days now, and need some help. First the layout.
In our setup we have an accelerometer with a movement interrupt pin...
I got this error when trying to use the button library to debounce noisy buttons.
My application is a peripheral.
When I looked in the library source I saw
#if NRF_MODULE_ENABLED...
I am working on a nRF52328 present in the Taiyo Yuden EYSHJNZXZ module. I am using an FTDI module for UART communication. I followed the steps in the following tutorial: link...
Hi everyone I'm Rookie....
Recently bought this board, want to do more applications in the expansion of the pin,
for example, control stepper motor or LED, but can not...
I am using the experimental_app_hrs_nfc_pairing_pca10040_s132 nrf52 example.
I want to set my custom uuid and I have followed the instructions given in the devzone.nordicsemi...
HEllo I am having an error saying
Undefined reference to
SEGGER_RTT_printf
I have looked into this post and tried it, however I am not able to fix it,I have defined...
nRF5_SDK_12.2.0.
app_timer_freertos.c
app_timer_stop() call xTimerStop/xTimerStopFromISR with timer_id parameter.
It seem to must use hTimer parameter.
It's bug?
MY application is using SDK 12.2, SD132 v3.1 and freeRTOS. I'm trying to debug a sensor that uses TWI. When I enable logging. #define NRF_LOG_ENABLED 1, NRF_LOG_BACKEND_SERIAL_USES_UART...
Hello Everyone,
I am new to keil and nrf51822 programming.
Currently I am using softdevice s130 with hex file for bootloader from
folder : nRF5_SDK_11.0.0_89a8197\examples...
Hello,
I would like to instruct my application to read the battery voltage on my nRF52pca1040 DK, I am intending to do so through the SADC.
I will feed the board with...
Hi,I have some problems in debug with experimental_ble_app_buttomless_dfu project.
First i build the experimental_ble_app_buttomless_dfu project,so i get the app_buttomless...
