This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Before I try something which is technically impossible....
Does anyone know if the USB functions on the nRF52840 would work in the bootloader, or only in the application...
I've recently tried add App Data (pstorage) to my Application. Thus I want to preserve this data over DFU Updates. To do this I updated my Bootloader to reserve App Data during...
Hi
I am using SDK11 with S130, NRF51822 that using ANCS and facing bonding problems after reach the max bonds.
Reference to nRF51-ble-peripheral-bond-handling example,
...
My application is doing kind of old communication with an old machine.
Communication line is bit banged by an GPIO. Baud rate is 0.5ms.
"Start bit" is still used to synchronized...
Hi,
I use nRF52832 with sdk 12.2.
and I running the ble_app_hrs_c example code on pca10040 evb.
I can scan many hr devices but polar h7 heart rate not.
I check Iphone...
Hi I use nRF52832 and move my project to SDK13.
I want to use debug mode in keil-c and try to find after ble_db_discovery_start function call why no csc_c_evt_handler_t call...
I'm working on an OTA firmware update process, using my own bootloader and application. To understand the process' limitations, I need to know to what extent one can update...
hello everyone：
how many timers can i open in nrf51822(QFAA) with SDK9.0? the APP_TIMER_MAX_TIMERS's max value
#define APP_TIMER_MAX_TIMERS 13 /**< Maximum number of...
Hello,
I am referring to this link
www.nordicsemi.com/.../3rd-Party-Bluetooth-low-energy-Modules
and I am referring to Xuntong PTR5518 11 15x15x2mm PCB China product...
I see BLE_GAP_EVT_SEC_PARAMS_REQUEST generated from SD. How to call this request for pairing state?
I can't find any peer manager in the project.
Explane, pls.
Following is a simple application that I have created. It has no softdevice and the configuration is very similar to blinky freeRTOS example.
Source code:
main.c
...
Hello ,
I'm working on custom board, I'm trying to disconnect from the Central (Andriod app) when the battery is below certain level and stop re-advertising.
Below is...
In s130 Soft device v2.0 document, it says it can have role with up to 8 Role concurrent with Central, Pheripheral, Advertiser, Observer.
I'm not sure i've understand all...
Hello. I'm using nRF52832, PCA10040, SDK13, S132 and "ble_app_uart" as reference.
When I connected board through by bluetooth, I couldn't see notification message which...
Hello,
According to the nRF Sniffer Guide 1.2, the sniffer is supported on a number of platforms (nRF51822/nRF51422 Evaluation Kits and others). All of them (as far as...
