Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
I used to able to get the blinky example in SDK11 to work. But for some unknown reason I couldn't scan my device using Nordic master control panel. The LED1 will be turned...
Can the nRF52 output the 32.768kHz clock on a GPIO. If so, do I need the 32.768kHz xtal, or can I output the generated clock from the 32MHz xtal? I need this clock to sync...
Hi
Yesterday I downloaded the new SDK12 and checked what changes could be relevant for my ongoing/next projects.
One remarkable thing was the fact that almost any peer...
Hello,
I'm trying to upgrade the application on my board via OTA DFU but it seems to fail if the app file is greater than 64KB:
DFU fails with my app which is 70kB and...
Hello!
I want to connect the MCP9808 with the nrf52832. Therefor I use i2C.
My example on the nrf52832 is the:
<nRF5_SDK_v11_0_0 folder>\examples\ble_peripheral\experimental_ble_app_eddystone...
Hi , I am using nRF51822 as a ble_peripheral to send the sensor data to the phone. I already add a characteristic with the property of notify , and it could work when using...
Hello,
I've been working with the SPI Slave on a nRF51-DK for several days. I am using the nRF51-DK (PCA10028), S130 v1.0.0 and SDK v10.0.0. First, I set up a RX and TX...
D:\nRF51822\mergehex.exe --merge D:\nRF51822\s110_nrf51822_7.0.0_softdevice.hex _build\ble_app_hrs_s110_xxaa.hex --output hrs.hex
I am doing it.But one of the files to...
hi i am working on nRF51822 chip, trying to flash code using keil IDE through STLink debugger. which i have attached image . while flashing the code it is showing Flash is...
I have a peripheral that pairs to a central and establishes a connection (without bonding) without any trouble. When I disconnect the central (e.g. cutting power to the central...
Hello All,
For the S120 softdevice active scanner, it appears that when ADV_IND is received and a scan request/response exchange occurs there will be two BLE_GAP_EVT_ADV_REPORT...
Hi,
I am getting the NRF_ERROR_INVALID_STATE error when I call dm_security_setup_req in my security timer timeout handler. The function's description says I'll get this...
Hi,
I would like to store firmware version number at a particular offset from the application start address so that it can be retrieved by boot loader as explained here...
The comment in dfu_init_prevalidate says the following
// To support application versioning, this check should be updated.
// This template allows for any application...
