I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
Dear all:
error occured when I was programming application hex in nRFgo Studio1.20.0,just refer to "program application error.png" ,the error shows "programming failed...
I have a sensor device that needs to transmit every so many seconds. I am looking for a code example to run on nRF52-DK that will do this, sleeping inbetween transmissions...
According to the Gazell using the 1MHz spacing for each channels and the DTM using 2MHz spacing.
Then can we use the DTM channel 0 for Gazell channel 2 to test the Frequency...
I am looking for a nordic BLE development board that can do data transfer through the UART. Something like SPP (Serial Port profile).
Here is what I need;
The iOS and...
Hi,
Question regarding blog from Thomas Søderholm ( blog.nordicsemi.com/.../which-technology-should-i-choose-to-connect-my-wearable-device-to-a-phone):
Can't you do...
Keil 5.18a forces me to install "missing Software Pack"
I am trying to set up SDK 11, SD312, with Keil 5.18a, but when I try to load an example from the SDK 11 examples folder...
Hi! I have a nrf51 that act as a central and a beacon that is my peripheral, they connect to each other using is_uuid_present but I can't enable notification using db_discovery...
Hello,
I am currently designing a PCB containing the nRF51822 chip and I am concerned about how I will be able to update the program.
I have 2 main questions :
I...
Hi,
I developed an application with Nrf51822 with some bonding need.
No problem with android or using the dongle, but using iOs systems it happens that after a random attempt...
When I add a GATTC in S110-V6.0.0 ,my GATTS stops working,the NRF Master control panle retern ERROR(0x85):GATT internal ERROR Error(0x85):GATT ERROR .Can S110-V6.0.0 run GATTC...
The note on the IoT softdevice says:
"This SoftDevice is a technology prototype only. Therefore, it should never be used in production."
Will there ever be a production...
Hi
I know perfectly it is not possible to debug while the softdevice is enable and the Bluetooth is working. When I try to set up a breakpoint under these conditions, the...
hello there i want to communicate nrf51 and nrf52 using i2c protocol. [https://devzone.nordicsemi.com/question/75218/i2c-in-nrf51/?answer=75221#post-id-75221]
from this...
Hi ,
I am working on the heart_rate_collector example code of nrf51-ble-driver_linux_0.5.0.
The program detail of nrf51 as below:
-- sorftdevice : s130_nrf51_1.0...
Good morning,
I have designed a prototype based on nRF51822 device. Now, I want to program it with a demo software and I have the Ulink-me tool instead of Segger. From Keil...
