But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hi!
I have inherited a large codebase that I'm trying to migrate to SDKv10 from SDKv6.
The project also uses an A4960 BLDC motor controller. To bring the motor up to...
Hello,
Is my ram reservation right for nRF52 with S132 ?
see in app_ram_base.h APP_RAM_BASE_CENTRAL_LINKS_3_PERIPH_LINKS_1_SEC_COUNT_3_MID_BW = 0x2F50
RAM (rwx) ...
Hey,
I have been trying to create a notification characteristic for nrf51822. Whenever I add char_md.char_props.notify = 1; lightblue doesn't connect to it.
I do get a...
Ok, this one seriously has me stumped...
I have a custom bootloader that is modified from the DFU example (SoftDevcie S110 8.0, with SDK 9.0, using gcc). BLE is not used...
What is the distance that a nRF24L01+ correspond to for 0db, -6db, -12db, -18db output powers.?
I mean what will be range of the chip for these output powers.?
Thanks...
Hi all,
Hope someone can help me. We are using the NRF51822 on MDBT40-256V3 module. The IC used is revision V3. We're not using Bluetooth but our own proprietary protocol...
On loading the ble_proximity_template Arduino sketch, i get this message "Remove the wire on Pin 6 and reset the board for normal operation." even though there is no connection...
Hello,
Is there any tutorial about how to sign an update for dfu bootloader ?
How can I generate a pem key with dfu_init_template_signing.c Qx and Qy keys in C style ...
Hi
I can't find the soldering profiles for the nRF51822 and nRF52832. Are there any specifications I'm missing or is there a standard profile you suggest?
Thanks for your...
Hello,
Bootloader jump on DFU_BANK_0_REGION_START.
DFU_BANK_0_REGION_START = CODE_REGION_1_START = SD_SIZE_GET(MBR_SIZE) but if i watch value, debugger says it's 0x3008...
Hello,
I am using the nRF52 along with SDK 9.0.2. I have used both the ble_app_uart code and the twi_master_slave code to send data from a sensor over bluetooth to the...
Can anyone explain the difference to me between the two SDKs?
it seems I can use them both for nRF52 development?
they both support the S132 soft device
Which...
i use nrf52 DK as master and configure ads1292 breakout as slave. I have try the loopback example which works properly. I write the sample spi code based on spi_master_with_slave...
ble_app_uart_s110_pca10028
i need function is press button to erase bonding information, then use App to connect and bonding.
How to implement this function? could you...
