I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
When i try to run or debug the ble app uart example on our own hardware using the nrf52810 there is a fatal error when executing the code.
The example does run on the...
Hello
I am using nrf5340 raytak board which does not use DC_DC power, uses internal quartz. When I play the Bluetooth peripheral example I get the following error(I using...
I'm trying to build a simple water leak detection system. The sensor would need to alert a user through SMS/mobile notification when a leak is detected.
I was thinking of...
hi, I am working on to combine USBD CLI and RTT to USB HID with SDK 17.10, configuration as below
pls see below mainloop:
other codes are based on example of USBD...
This is driving me totally nuts. There are inconsistent pieces of information in documents and code. I am getting a modem reset loop problem. The documentation says the timer...
Hi,
Long story short, I made some boards using nrf9160 modules, received parts from DigiKey, soldered but can't make them work, at all.
nReset pin is stuck low. Tried...
I am using nRF52832 for high-rate sensor.
Of course, I can use SPI using CPU but it's busy for other jobs.
So I want to use DMA if it's possible.
Currently I am using...
I am using the nRF5340 and trying to get MCUBoot working. I am running into problems and looks like I need to edit the MCUBoot code, the problems are long and numerous too...
Hello everyone,
I'm using the Bluetooth Peripheral sample UART and have noticed an issue.
When I perform a lot of sequential pairing requests followed by cancels from...
I recently bought this display that is 64x32 pixels and uses the SSD1306 driver . When running the LVGL Basic Sample with the Zephyr ssd1306 _128x64 shield , the display works...
NRF52840 uses 2.5V power supply. We found that when the voltage drops below 1.7V, even if the voltage returns to 2.5V, the entire system cannot work and JLINK cannot connect...
Hello,
We are using the npm1300 PMIC to run the nrf5340 VDD at 1.8V. If we connect D+ and D- from the USB port directly to the D+ and D- pins, will the USB peripheral...
I am developing a custom nrf5340 board design, that is using the BL5340PA external antenna module to implement the nrf5340 chip in the design. The BL5340 module allows all...
