Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hi,
The Thingy 91 X uses a shared antenna for BLE and Wi-Fi. I can see from the Hardware Guide and the schematics that there are several hardware connections between the...
Hi,
I am working on implementing the BME680 sensor with the nRF5340DK using the I2C protocol. I have successfully obtained the slave device address and the sensor address...
Dear Team,
I am experiencing issues updating the firmware image on my custom board based on the nRF7002, using an external SPI NOR flash ( is25lp064 , 8MB). The board...
Hello, I’m trying to compile code for a u-blox C209 AOA Tag. I installed the nRF Connect Extension Pack and was able to build normally.
After adding some unrelated paths...
Hi everyone!
My name is Natalia, and I’m just starting to work with Nordic. This is my first design, and I’m trying to connect the nRF7002 module to the nRF52840 microcontroller...
As part of a university project I am trying to read an analog signal and transmit it at the maximum data rate over ESB. But I cant seem to get above 1700kbps without any of...
In https://docs.nordicsemi.com/bundle/ps_nrf54L15/page/uicr.html#register.BOOTCONF, I can seee that it is possible to apply Read protection to the first x kB of the RRAM by...
I have problem with i2c that can't read the cst816s, its always return log message `<err> cst816s: failed reading chip id` and `<err> cst816s: Could not read x data` when...
i have some bare-metal RF code that runs on my nRF52-DK, which i'm currently porting to my nRF54-DK.... functionally, everthing is working just fine -- the boards can in fact...
Hi
I am trying to port some PWM code from the NRF54L15 it uses HAL access because i have found it has faster writes which are useful for my application (testing latency...
I implemented the function of DFU using NRF SDK 17，Implemented dfu using MCUboot with ncs 2.9.0
Can the dfu of MCUboot in ncs 2.9.0 upgrade the program of nrf sdk 17
I'm hitting a wall with implementing nRF7002 + nRF52840 without Zephyr.
I've worked with nRF52's for about 8 years now and on about 30+ products, all using the original...
Hi, I'm using the nRF52840 DK with SDK 17.0.2.
I've set selective_auto_ack to true , which should allow the use of dynamic ACK (or ACK payload).
I have two types of data...
Trying to get set up with my new PPK2. Installed NRF Connect and JLink on my Win11 system. When I select the device in the Power Profiler software I get an error. Searching...
Hello,
I am trying to download nRF Connect for VS Code extension but the extension is not found. There is just no result when searching for 'nrf connect' or something...
