I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
In nRF51 SDK 7.1.0, there is a c header file using c++ keywords operator .
Here is a snippet of components/ble/ble_racp/ble_racp.h using the keywords.
/**@brief Record...
To the kind attention of Nordic support team,
I'm running ble_app_hids_mouse_pca10100_s112 in a PCA10100 dev board. It is the sdk17 program, where:
1.I added 2 files ...
Hi there,
We are currently running tests on the nrf9160 DK using an iBasis SIM card, which should be capable of connecting to multiple networks. We are trying to understand...
Hi,
How is the LTE-M or NB-IOT network availability for very much remote locations like forest or mountains for emergency use cases compared to low-earth orbit satellite...
NCS ver: 2.0.1
chip: nrf52840
node: MTD not SED
network: one OTBR as leader and one MTD as child
After about 4~10 hours, MTD will offline. Sometimes it can reconnect...
I like to enable compiling my code with c11 or c17 but when compiling with west this does not seem to be possible.
To force the compiler to use c11, I used option:
CONFIG_COMPILER_OPT...
Hello,
I am experiencing a SoftDevice Controller ASSERT: 62, 1846. I am using a nrf52832 acting as a peripheral and nRF Connect SDK v1.9.1. This assert happens when large...
BLE-app-blinky client not working
BLE-app-blinky sample build success, LED1 on, when connect LED2 on, but i can not see client service uuid in my android app.
i cannot...
Hi there,
We are doing some testing on an eSIM with the nrf9160 DK, and we are looking for an AT command that can be used to read the eUICC ID of the SIM. We are using the...
Hello,
We are planning to integrate the LwM2M carrier library. Our system uses mfw 1.3.3 and NCS 2.1.0.
Based on the following page https://infocenter.nordicsemi.com/index...
I'm trying to update MCUboot from the application. As a first test, I enabled the flash shell commands. I can erase somewhere within the flash without problems:
uart:~$...
Hi,
I have a simple SPI circuit to read data from a flash memory W25Q64 to be exact and I have difficult time reading the device address of the chip through SPI.
The situation...
Hi Devzone,
we are working on nrf5340 mcu, from the DTM sample, l learned that the application run on network core only, but my application scenario is combine the DTM with...
Hello,
I'm using the SAADC voltage conversion formula from the Nordic example as follows: 10 bits are used in the example.
By the way I want to change ADC resolution...
This is a follow-up to my previous post . I'm developing a BLE Peripheral application on the nRF52832 that uses NRF_SDH_DISPATCH_MODEL_APPSH to receive events from the SoftDevice...
