When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Hi,
I'm trying out S130 SoftDevice. I have 1 device with S110v7 which acts as a peripheral.
2nd device contains S130 0.9 (I've based my code on S120 multilink central example...
I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi,
I tried every configuration options one by one to change the MTU size, but it doesn't work.
I connect to nRF52840 with Raspbery Pi and when I subscribe to a notification...
Dear All,
I am trying to figure out the maximum current consumed during the NFC operation.
I am using nRF52832 and writable_ndef_msg example from the SDK (LED, flash write...
My previous post and the response I got was hugely helpful to my understanding ESB on the nRF52. Now that I grasp the basics, I felt it was appropriate to create a new post...
Hi,
quick question..Which, if any, Nordic device has NFC that can be read and write without additional NFC ICs?
I've got an NRF52840 dev kit but apparently it only supports...
To the kind attention of Nordic support team,
we are (re)working on an old legacy project using nRF24LU1 and gazell protocol. We would need to know if there is some simple...
I am trying to add this ultrasonic sesnor driver ( inductivekickback/hc-sr04: Zephyr RTOS driver for HC-SR04 Ultrasonic Ranging Module (github.com) ) and testing it with the...
Hello! This is my problem.
SDK：SDK17
Softdevice : S140
Board: nrf52840
The connect interval is 135ms. But the latency I test is larger than connect interval. So...
i use 2x nRF52840 DK as DUT and Lower tester and DUT, my windows laptop as the Upper tester, and use python code from nan_34 Setting up production test using DTM.
as below...
We just got the PPK2 delivered but it won't turn on. If we plug it in using "power only" it lights up but it doesn't do anything when we plug in the "data/power". It also...
hello
I used nrf52840 with SDK15.3.
1.I use the example in this ticket and adjusted the baud rate to 9600 without hardware flow control. After SES is compiled, an "NRF_ERROR_SVC_HANDLER_MISSING...
MM8130-2600RA2
https://www.digikey.in/en/products/detail/murata-electronics/MM8130-2600RA2/1775922
This is RF connector used in DK. Please provide us the mating...
Hi there.
I am currently learning mqtt_simple from the nrf sdk example. So, I was trying to create a hex file that build using nrf9160, because I can't build it on thingy91...
Hi,
I have a custom board which uses P0.02 and P0.03. They are connected to interrupt signals from external devices.
To configure them as GPIO I set CONFIG_NFCT_PINS_AS_GPIOS...
Hi
I am developing a custom board using nrf9160. But before jumping to that process, I am using thingy91 (nrf9160 chip) as evaluation board for check all the firmware works...
