Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Hi,
I'm trying out S130 SoftDevice. I have 1 device with S110v7 which acts as a peripheral.
2nd device contains S130 0.9 (I've based my code on S120 multilink central example...
I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
Hi Nordic!
I'm a fan of your products and usually work in Segger Embedded Studio (used it with nRF Connect SDK v1.9.1).
In that application you can create a "blank"...
Hi,
1. I would like to know which rexample should be used when using nRF52820 as master and slave?
2. How many slave can be connected at most?
Thank you for all your...
Hi, Working with nRF5340 in NCS 1.9.2, I've overridden weak usb_update_sn_string_descriptor function to set iSerialNumber at runtime. I wanted to read the actual serial number...
Hi, I am currently working on moving our app over to PSM mode.
We have earlier used manually disabling and reenabling the modem when sleeping, using LTE and getting GPS...
hi, I am trying to use Hal_Atomic_Start() and Hal_Atomic_Stop() to imply an atomic block, in order to avoid interrupt from system when execute the atomic block, source code...
Hi,
The nRF UART running over the ASYNC interface consumes a lot of current even when not in use. As ours is a battery-operated device we intended to disable UART when not...
hi
im working with a custom project which can flash easily on a eval board im trying to add dfu for my project but it didnt work hence i added my project into the buttonless...
Background:
In pursuing development of Thread-enabled devices for use in home automation, especially using the just announced Matter 1.0 protocol, the nRF52840 Dongle is...
Hello,
in my device tree there are three nodes/items concerning battery Management:
One load enable pin
One measure enable pin
the required ADC configuration
...
Hi Team,
We are currently using nrf Connect SDK 1.8.0 and developing our application using nrf52833.
Currently we use our own git to maintain our application and nRF...
Hello, When enabling the Sensor system and having a qdec device enabled in my dts I get the following error:
This seems to be a bug with the Zephyr code checking a const...
Hi,I'm using nrf52832. I configured P0.20 as GPIO output,P0.22 as GPIO input.These two pins are connected wiht a 10Kohm resistor.I measured the voltage level on P0.22 is about...
Hello DevZone,
I'm using nRF5 SDK for Thread and Zigbee v4.2.0 and trying to test Zigbee OTA example.
I'm following this guide https://infocenter.nordicsemi.com/index...
Hi,
I am working on thingy91, I have created/added a BMS module in the project which gives different values for different data fields.
Everything is fine as BMS is transmitting...
Hi,
I am using TWI channel0 on my nRF52833 as master to get readings from a few sensors.
I need my nRF52833 to communicate with another microcontroller over TWI/I2C so...
