Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hello
There has been an interesting braking change between SDK v3.1.0 -> v3.1.1. When using PSA (CONFIG_MBEDTLS_USE_PSA_CRYPTO=y) and a server with signature algorithm SHA384withECDSA...
I'm developing a project, where I use nRF9151 as a GPS sensor, and nRF52833 as a BLE gateway. I want to send data from 9151 to 52833 over one of UARTs. The problems I'm facing...
Hello,
I’m currently working on a hardware design using the following components:
nRF54L10 SoC
nRF21540 Front-End Module (FEM)
2450AT18B0100001E chip antenna...
I'm developing a project for nRF54 using NCS. I have a question regarding the placement of the BLE protocol stack. In the previous nRF5 SDK, the protocol stack was usually...
I have downloaded the nrf connect software and downloaded the segger drivers. I cant see the drivers in mi windows drivers administrator. The evk is powered by the usb because...
Hardware env: New designed board with NRF52840 + NRF9151, which 52840 connect 9151 via uart
Software env : NCS version: v3.1.0 (new installed) Nrfutil version: 8.1.0 (34e21a1...
Hey, since iOS version 18.6.2 the BLE connect to our BLE peripherial with nrf52840 getting disconnect events. Also the range between them is very bad. The connection parameter...
I'm currently working on some projects for the nRF54 platform using NCS and VS Code. I want to delete the unused files in my project because the codebase has become too large...
In the nRF52840 Product Specification PDF v1.11, on page 323, the third paragraph down states:
1. "If the CPU performs a clear operation on a bit in the LATCH register...
Hi Team,
below mention errors I am getting west build process.
* Executing task: nRF Connect: Generate config HVPP_BLE_Board_Files/nrf54l15/cpuapp for c:\Haritha\Github...
hi support team，
customer told me 54L15dk debug out is not able to program another 54L15 chip.
so i tried,
1. A-54L15dk debug out program B-54L15dk debug in, failed...
I'm trying to leverage the asset tracker project form nordic 9160dk to actinius icarus 9160 board, i use tagconnect 2030 to connect P19 of dk and icaurs, but the jlink cannot...
When I try to add OTA image compression for MCUboot, the RAM utilization skyrocks and is not compatible with the nrf52833. Is there any way to cut out any and all excessive...
