Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Hi,
I'm trying out S130 SoftDevice. I have 1 device with S110v7 which acts as a peripheral.
2nd device contains S130 0.9 (I've based my code on S120 multilink central example...
I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using slightly modified master SPI example from here which is running on nRF5340 to communicate with slave device, which is RHD2216 . SPI frequency is NRF_SPIM_FREQ_4M...
Using a nRF52832, I would like to broadcast advertisement packets normally and in extended mode at the same time. Is this possible or do I have to ping-pong between, stop...
ok,i recenlty have gotten iq samples from Rx.but i think my received iq samples are from Tx .i use the NCS 1.9.1 with two boards nrf52833dk.
firstly,i connect antenna array...
Hi, I have already updated all certificates and firmware. But when I am trying to connect my device to the cloud it does not recognize my device. when I am trying to add my...
Hello Dear,
Why the time of uplink state is 950 ms if the data packet size is 0 Byte in mode NB-IoT not in LTE-M?
Can we say that every time a data is sent, it takes 950...
Hello, All
I received following message when I test the code, it appears on both sides,
ASSERTION FAIL [chunk_used(h, c)] @ WEST_TOPDIR/zephyr/lib/os/heap.c :163
unexpected...
Hi,
I have installed Segger Studio for ARM v6.22a.
I have also installed the SDK5 version 12.3.0.
I imported the IAR project project ble_app_start_notification_pca10028_s130...
Hi,
I am after some assistance with creating a 6 layer stackup to use with the NRF52840_CIAA that is 1.6mm thick.
Can you provide recommend layer stack up that have been...
Hello.
Is there any difference between i2s hardware in nRF52840 and nRF52833? I made WS2812B i2s driver and working very good on nRF52840. The same code (project is adjusted...
Hi, I'm developing an application which is merging from (ble_app_uart + libuarte + app_timer + pwm). Here is my main.c Now I'm developing an feature that using timer ((app_timer...
Hi,
As mentioned in subject line, I am trying to enable BLE SC peripheral in SDK 17.0.1 with softdevice S113. I have enabled the PM_LESC_ENABLED macro in sdk_config and...
Hi Nordic,
My customer has imploy nRF52832 to develop a heart rate equipment.
We have test the ble_app_hrs_c and ble_app_hrs on two nRF52 DK.
I found that if I comment...
Hello Dear,
Why the time of uplink state is 950 ms if the data packet size is 0 Byte?
Can we say that every time a data is sent, it takes 950 ms to get the transmission...
Hi nordic, In the products I developed, since the entire product is metallic, only a small part is a non-metallic material, and an antenna has been designed to solve the problem...
