Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hi!
I am trying use aws iot sample and over this the gps example to obtain location and transmit a aws iot core, but I have problem with manage of lte and gps functions...
My project uses nRF52840-DK to connect, bond and discover a custom service with two characteristics (TX and RX) and RX Characteristic has a CCCD (0x2902).
The flow of the...
I am using nRF5340 DK board to implement zigbee network.
I have just build connect SDK's zigbee example (network Coordinator) and seen utilization of RAM shown below.
...
Hello everyone.
I am trying to set the attributes' value of a custom cluster I have defined.
I have defined 2 attributes:
I have followed the same procedure...
Hi,
We are designing the Nordic 52840 into a product and had some questions about the power configuration:
For both REG0 and REG1, are there any downsides to selecting...
SDK version: nRF5_SDK_15.3.0
Platform: nRF52840 DK
--
I use ble_app_blinky example and use nrf5-calendar( https://github.com/NordicPlayground/nrf5-calendar-example ...
Hi,
I am new to nrf9160 and zephyr. I was using the SD card and a breakout board on SPI bus to write the raw data coming from the PDM interface on nrf9160 Feather. Before...
Hi Nordic DevTeam,
I have successfully done DFU through nRF Connect both on Android and iOS after merging ble_app_uart (combine ble_dfu_buttonless application here) & secure_bootloader...
Hi,
I am developing projects for street lightning system and I use in my projects many CoAP libraries. In my projects I use OpenThread and some peripherals like UART....
Hi everyone,
I use the nrf5_SDK_for_Mesh_v4.1.0_src, I would like to reduce the time it takes for a device to connect to a bluetooth module as a proxy. For the moment this...
Hello all,
I try to get the asset tracker v2 to work against a eclipse mqtt broker. For the first steps I use the mqtt.eclipseprojects.io broker before I hosting my own...
We are developing a device with the nRF52805 for BLE communication. The firmware was developed for nRF52832 and converted to nRF52805 following Nordic's documentation. The...
Dear Nordic support,
Could you please give an advice regarding usage of Zephyr SPI driver / NRF SPI driver with Nordic nRF52840? I've faced with the issue that driver can...
Hi!
I've shipped a whole bunch of PCBs out to customers where pin P0.21 is attached to an IC (which pulls it low by default).
Usually this is fine as the preinstalled...
