Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Hi,
I'm trying out S130 SoftDevice. I have 1 device with S110v7 which acts as a peripheral.
2nd device contains S130 0.9 (I've based my code on S120 multilink central example...
I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
Hi all,
I was going through the nRF Connect SDK tutorial and was trying to get the "Hello World" example running on a nRF5340-PDK (PCA10095, 0.8.0).
Before that I was...
Hi
i was trying to setup spi_2 for external sensor interface with nrf9160-dk but even after setting CONFIG_SPI_3=n and CONFIG_SPI_2=y the spi_2 enabled but spi_3 isn't changing...
Hi, I try to implement adding a custom service to the BLE GATT stack by following this tutorial , but I faced a problem which looks like a linking problem
So far, I finished...
I am testing the "ble_app_hids_keyboard" program on the nRF51822 Evaluation Kit. I changed the pin assignment in nrf6310.h and it compiles fine. When I run the program it...
Please provide sample code on how to configure pins to control Relay Shield from Seeed on nRF9160 DK
https://wiki.seeedstudio.com/Relay_Shield_v3/
I have used the following...
Developing on the nrf51822
Have working code for the nRF52840 Dongle using the pc-ble-driver therefore all Bluetooth work is done using sd_* calls. The PC provides easy...
Hi,
I have driver file in my project. I did copy of it and add to my project instead of the old one(paths in preprocesor definitions and includes have been also changed...
Hi,
Is it possible to send entire array over ble?
Char *data100];
For (I=0, I<100, I++)
{
Data[i] =timestamp_data;
Ble_nus_data_send(&m_nus, &data,size of (data...
Hi,
I have a custom NRF52810 board in which i flashed modified code of low power ESB example and is working.
but when I flashed along with the bootloader, the application...
Hello,
We have a custom board with nrf52832. We have seen a problem during production. Our process is as follows (the below steps are ran in a script),
1. We recover...
I think the nRF connect SDK uses RTOS since it is based on Zephyr. Is the Bluetooth SDK using bare metal? What about the Bluetooth Mesh SDK?
Thank you for your time.
Hi there,
I'm currently working on getting a streaming application running which is supposed to sample some audio at 16kHz and send it (uncompressed) to a central device...
