i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
I'm building some of the samples using command line in Ubuntu and have a strange issue. Everything builds fine, the merged.hex file is generated, however when I try to flash...
Hello All,
Currently i am working on nrf51422 DK board(PCA10028). I am using SDK 12.3.0 ,from this i have referred the ble_app_uart example for implementing the UART and...
Hello,
After following the steps of the tutorial : https://devzone.nordicsemi.com/nordic/cellular-iot-guides/b/getting-started-cellular/posts/getting-started-with...
I have an application that works on nrf52832 that when it is powered on is expected to read a sensor data for initial 10 seconds if any, and then start BLE advertising for...
Hello Nordic Team,
I have an application where i am playing some samples over i2s to an audio amplifier. The application also uses fds to store those samples (they can be...
Hi Sir,
In the latest datasheet (52832_v1.4), our reference schematic shows the cap (C6) of DEC2 can be NC.
For DEC2, it is 1.3V regulator supply for Radio, may I know...
Hi
I am giving a try to ESB as an alternative to BLE. I am starting with esb_prx and esb_ptx sample.
That sample works on DK boards.
In order to save energy I would...
Hello to all,
I am using nRF52832 DK with sd132, v6.0.0 and sdk 15.0.0, segger embedded studio. We want to achieve change application timer time (APP_TIMER_TICKS(update_time...
I use nRF52810 and S112 as the soft device. And I use SDK 15.2.0. My BLE device works as a peripheral. And I have to connect some iOS and Android devices with bonding. Communications...
Hello,
I have a problem, I want to measure the power consumption of the nRF9160 with the nRF9160 DK, and I have the N6705B power analyzer, and I like to know how the connection...
Hello dear Nordic community,
We have developed a custom board that contains the nordic nrf52832, which is communicating via I2C bus with a 9-axis sensor (Bosch BMX055...
I am using Softdevice 140 with SDK v15.2 on Segger studio to develope a ble application. when Debugging, the program gets stuck as shown in the attached video. However, the...
Hi, everyone,
We are developing BlueTooth projects on NRF52832 and NRF51822 modules. The projects are built from DFU Bootloader, Soft Device and Main Application. Each one...
Hi Sir,
For EN 300 328 V2.1.1, I reference below setting.
https://devzone.nordicsemi.com/f/nordic-q-a/21643/en-300-328-v2-1-1-receiver-blocking-test-setup/84959#84959...
