Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hi,
I try to implement the nrf52832 as the TWI slave but get the following error messages:
I have added the nrf.twis.c to the project, included in the main application...
Ummm. :)
I'm hoping that I've done something silly.
It looks like I'm unable to configure a project.
Because the save option has vanished.
Another observation...
I am developing a Central/Peripheral application with SDK 15.2.0 for s132 device on nRF52 development kits. I switch back and forth between my application and the example...
Hi, I'm having a bit of an issue with the proxy_enable() & proxy_start() functions when they are used in tandem with the flash manager module.
Some info on my setup:
...
I would like my BLE device to communicate with Desktop using HID service & with a phone using custom gatt service. I know its just adding one more service but is it possible...
Hello All,
I'm trying to create a client device that toggles LEDs on a server on and off using the NRF52840-DK.
My modified Client code is giving me Mesh error 5 when...
In which state are the configured UART pins if the device is held in RESET for nRF52832?
We want to use the UART to communicate with the host without the nRF52832 in certain...
Hi, I have a project where an STM32 controller has the updated binary file for nRF1822 in flash and it will upgrade the firmware on nRF1822 with the serial implementation...
I am trying to add "Softdevice_handler" to project under nRF52 SDK_15.0.3
But i couldn't find "Softdevice_handler" in nRF SDK_15.0.3 and it is there in SDK 11
How to add...
Good afternoon,
The 'sd_ble_gap_device_name_Set' seems to have a limit of 10chars when defining the device name. In principle, it should be 31. Why do I have this limit...
Hi
I would like to use a 2.4Ghz remote controller for a project but I did not find any example/documentation on how to use 2.4 frequency with my nrf52.
Can someone...
Hi
I would like to use a 2.4Ghz remote controller for a project but I did not find any example/documentation on how to use 2.4 frequency with my nrf52.
Can someone...
nRF52840-DK 2pcs, one TX broadcast signal software, one RX software. RX can receive TX.
My nRF52840 product 2pcs, one TX broadcast signal software, one RX software. RX can...
Hi,
I am working with a motion sensor which sends a message when it detects a motion. I am communicating between the nRF52 DK and the sensor via UART. I am able to receive...
Hello,
I am interfacing nRF52840 DK with the MAX30101 sensor. I am able to execute all the TWI transactions necessary by using port 0 pin 27 as SCL and port 0 pin 26 as...
