Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Folks,
One of the devs here found that all warnings were switched off in SES, so I've recompiled and got rid of most of the 1400 odd (sic) warnings by suppressing unused...
Hi
I want to use loggers in the program. I understand that the code itself uses NRF_LOG. But I do not understand where those log details are printed. So, how do I create...
I am experiencing an immediate BLE disconnect when trying to use DLE. I can write up to 20 bytes of data, but if I try to write more 21 bytes or more I get an immediate BLE...
I was wondering what I have to do to clear all stored mesh data on flash.
Do I have to initialize the whole mesh, or can I init only a subset?
What do I have to do so...
Hi all, I am working with NRF52840 and Open Thread SDK V3.1. Everything is normal.
But now, I want to run open thread example in SDK with NRF52811. T o reduce product costs...
Dear every one
I have a project with nRF52832 dev kit. I want it sleep (mode on) and wake up every 2 minute. When it wake up, it broadcast BLE and if it sleep it not broadcast...
I have a custom PCB that I designed for use with the nRF52811. I have tried to connect to it using the nRF Connect Programmer to program a Soft Device but I am unable to connect...
dear folks,
I bougth my dev kit last week from digikey. I tried the asset tacker demo out of the box without success. I tried nearly everything. Updated the modem to v1...
Hi,
Is it possible to use RTC for timekeeping along with app_timer functionality?
For example, I want to use simple RTC counter register and overflow interrupt to provide...
We are using ble app uart example in gcc. The uart event handler is not responding on APP_UART_DATA_READY. When it was build on keil it is working, but due to necessity we...
OS in development environment ：Windows7 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex-M4F 32 bit processor...
Hi guys,
I want to use a smartphone as a poller and the NRF52832 as a tag device. I use typical, high-rated apps desired for sending and receiving data by NFC. I tried the...
Hello, this is my first post on DevZone:-) I'm working with DWM1001-DEV board. I know that this board contains an nRF52832. I'm configuring the SAADC to measure the battery...
Hi
When I use the SDK 15.2.0 & Mesh 3.10.
This light_switch example of advertising bearer(Mesh Profile 3.3.1) default to using the channel 37.
So,I try to change the...
