When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Hi,
I'm trying out S130 SoftDevice. I have 1 device with S110v7 which acts as a peripheral.
2nd device contains S130 0.9 (I've based my code on S120 multilink central example...
I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Sir,
System notifications where enabled On my mobile but still I did not get any kind of notification from Eddyston Beacon-URL.I am using nRF52840. Is there anything such...
Hello!
My project programmed on the nRF52dk board.
Using the twi protocol for communication with other driver IC.
Below code is twi_init source.
---------------...
Hi,
I am trying to transition from nRF51822 to nRF52840. I have the PCA10056 board to help me with the transition. I was able to make the BLE work with the nRF51822 by flashing...
Hi
I would like to read values from three AD channels where I use different sampling frequencies and different number of samples are captured at each sampling frequency...
Hi all
Recently, I have been developing a BT module using nRF52810. However, the module couldn't communicate normally with STM32 via UART as the MCU keep rebooting. And...
I am using the BMD-350 in a new device that reads off of a sensor and changes the alert level in the IAS based on the value. Implementing the client on this peripheral, I...
Hi
I'm trying to use the nRF52840 DK debug out to program/flash an external nRF52840 IC that runs at 1.8V logic level. According to the manual, the DK is running at 3V...
When running our hardware using the J-Link debug in connector on the dev kit, BT is fully functional. But when we try to run using the very same power source (ie, the dev...
Hi all,
I'm developing a custom board that is equipped with a nRF24L01+ (directly soldered on my PCB, no breakout). The board is equipped with a PIC32, that controls also...
SDK 15.2
port_cmsis_systick.c
nrf_drv_clock_lfclk_request is part of the legacy drivers that will eventually be removed?
Does this mean for FreeRTOS I need to keep...
Hello,
I want to set the nrf24le1 module into register retention mode with timers ON but clock source from XOSC32K. I need this power saving code in my project. Also can...
Hi,
I am using adafruit Bluefruit BLE SNIFFER. My question is whether it is required to use jLink along with it to connect to it via USB. Also, I have a question can I sniff...
sdk5 15.2's app_timer.h at line 61 says:
* @details Use the USE_SCHEDULER parameter of the APP_TIMER_INIT() macro to select if the * @ref app_scheduler should be used or...
