Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hello everyone! I'm new to bluetooth mesh or even to C programming and i don't understand the following: I want to send messages over Bluetooth Mesh from an nRF52840 to another...
I tried to install the CDC driver using nordic_cdc_acm.inf in the DSK15/examples/usb_drivers directory but the installation does not work and I get an error message when selecting...
Hi,
I tried several examples on nrf52840 dongle. Each one works well except usbd example. It hangs at the following code:
After investigation, the following simple...
Hi to all,
i am developing a device with nrf51822 and i want use it as a peripheral device, i want to write 4 packet per connection interval on noti char. i am ok with one...
Dear Nordic,
I just started with nrf52840 DK and my custom board. I derived my custom_board.h from nRF5_SDK_15.0.0_a53641a/components/boards/pca10056.h. I need to reroute...
use nordic demo example
i think the problem is crystal oscillator(external 32mb)
follow is the different:
//nordic kit board 0> clock state start*******************...
use nordic demo example
i think the problem is crystal oscillator(external 32mb)
follow is the different:
//nordic 官方开发板 0> clock state start***********************...
Hello,
we want to evaluate the nRF52832 chip with a example project. This project has the following functions:
- low power
- system wakeup by RTC running with external...
Hello,
I do want to simulate the behaviour of several nrf51 chipsets that communicate over the air. Do you have any suggestion, how to start with this? The best would be...
Hello everyone! I am interested in running some simulations to test a series of algorithms for BLE on nrf52832. Is there any simulator which can easily simulate nrf52832?...
Hi All,
This may not be 100% nRF-related, but:
I have a set of algorithms that are written with Keil uVision 5 for nRF52840 using the CMSIS-DSP library. Now, I would need...
Hi,
recently i made the mesh works but now i need to add OTA.
i've found this tutorial. I'm still trying to generate the keys... every time i try i get some error from...
I can read from the driver using appropriate instructions. But i am not able to write to any of the registers. Please Help. I have attached the functions and datasheet.
...
hi,
I’m new to nRF5x BLE devices.
I need to create a code for a project where i’m using a nRF51-DK device. So, I’m trying to demonstrate that the further the nRF51-DK...
