Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Hi,
I'm trying out S130 SoftDevice. I have 1 device with S110v7 which acts as a peripheral.
2nd device contains S130 0.9 (I've based my code on S120 multilink central example...
I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
The board has been working well.
Since one day, when I try to connect the board with my laptop using micro usb cable, the led5 starts blinking rapidly and I'm unable to...
Hi,
I'm trying to send and receive data to DATA interface that contains IN and OUT bulk endpoint (usbd_cdc_acm example). I'm using libusb on the PC side. It seems like I...
Hello,
I use PPK to measure the power consumption.
but I always get : Failed to start the PPK.
I have measured it last week and it is work.
and this is nrf connect...
Hi Team,
i am working on nrf51822 customized board, the SDK version is 12.3.0 (soft-device is s130 ) and Developing environment in keil 5.26 (on windows).
i am trying...
github.com/.../nrf52-ble-multi-link-multi-role I modified the code to access the environmental values and motion value
but if one thingy access one value such as temperature...
I develop an Android app which connects to a Nordic chip, and I cannot get the Android app to stop advertising once it connects to the central from the SDK multi link project...
Hi,
On the custom board I'm working on an nRF52832 uses the SPIS port with no CS signal (because of the HW connection with the master side of the bus). Since the internal...
Hi, i am trying to disable a signle GPIOTE channel via the INTENCLR. Here is a simple test case:
void gpiote_set_clr_test(void) { NRF_GPIOTE->INTENSET |= ((1<<3) | (1<<1...
Hello ,
I am working on a project in which two devices(one is central and other is peripheral ) uses Nordic bluetooth controller for connection and data exchange. nrf51822...
Hello!
I have been developing a BLE application on nRF52DK and used the ACN52832 as a module for a custom board for experimenting with BLE. I ordered a custom PCB from...
I am just starting using a Thingy:52 and want to use it with a C# UWP app. So far I have been able to retrieve the service and characteristics UUID's without issue but I am...
SDK 15.0.0 nrf52810 Example: Eddystone Beconing mode - ble_app_eddystone SEGGER Embedded Studio for ARM v4.12
I am using ble_app_eddystone example to advertise data in eddystone...
My development enviorment: SDK 15.0.0 nrf52810 Example: examples\ble_peripheral\ble_app_template\pca10040 e SES IDE
I am running above mentioned example without any changes...
Hi
I have a requirement to be able to re-start advertising with new parameters when told to do so over a Slave SPI interface. From other posts, it appears that there is...
