Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi， Nordic
I checked DFU operation, found DFU work in bootload mode.
I want to know below operation is OK or not. Plz help me check:
download DFU bootloader
download...
Hi, I use the PCA10040 v1.1.
This is an example of a PCB stack-up.
My questions are,
In the case of PCA10040, which is 4 layered, what are the values of...
Hi,
I am writing a firmware for one of my custom boards which use GPIOTE to detect interrupt for 3 GPIOs inputs (P0.03, P0.06 and P0.09, both with internal pull-ups) and...
Hello,
I'm trying to write my ADC samples over spi on a sd card (Using SAADC like in the sdk 12 example with PPI and using fatfs like in the example in the sdk).
I open...
I have been using the pc-ble-driver Python bindings to implement a peripheral. I have extended BLEDriver to support sd_ble_gatts_* the functions. I now have a working peripheral...
Hi All,
I am struggling with this question from many days. Does the SPI transmit or receive operation in SPI master code uses DMA? While using SAADC DMA I have specified...
I'm using an app timer to blink an LED while in the bootloader.
Initially I was configuring an app timer when the bootloader started up and never stopped it, assuming the...
After failing in replacing a Cortex M4 for a NRF52832 I'm studying the possibility of using a NRF51822 as a BLE controller, used by my Cortex M4 MCU.
As I saw there is...
Hello
Please tell me about sd_ble_gatts_value_get ().
Before execution, handle is 0x11, but after execution it will be 0x00.
Is this an abnormal thing?
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
main.c
something
hello there i want to scan perticular device. can any one helo me?? . i am using heart rate sdk 11 example
static void on_ble_evt(ble_evt_t * p_ble_evt...
Hello dear Nordic team,
we want to implement a white list to our central device in the production process. Bonding while producing is not an option for us.
Therefore...
We are having a project where temperature values will update whenever the temperature changes ,So I'm writing code like this
uint32_t ble_sh35_update_temp(ble_sh35_t *p_sh35...
I need to generate DFU init files on my Mac for OTA firmware on the nRF51. I haven't found a solution for a Mac-only environment (i.e. no Master Control Panel). I spoke to...
Hello,
I am looking for a SPI library which is simple enough to send and receive a byte from sensor. Something like this. for nRF51
spiwrite(ADDRESS, BYTEtoSEND);
val...
