Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi Nordic team,
Will the S310 stack be kept, feature- and revision-wise, in lock-step with the S110 stack?
To illustrate my question, can we expect the v7 S110 updates...
Hi, guys
I'm facing some problem in RF transmitting. While I used 51822 board being the device and compatible to nrf24LU1 as dongle. To analysis the problem, I need information...
Hello,
i am working with the s110 softdevice and built up a bluetooth communication. I wanted to reduce the number of advertising channels and read about the use of the...
Hi,
I need to send some additional information in advertising.
According to Core Specification Supplement v4 A.1.11 it is possible to use also 128-bit UUID in service...
My keyboard can't work some time,then I read back the hex from device. And I find that there are 4 byte be changed.
if I modify the left 4 red bytes to right. Then programm...
In my opinion, S120 can only acts as central role and can not be discovered by bootloading sponsor which is usually a PC program. More development work is needed if bootloader...
I am trying to run the bootloader example that comes with the SDK 5.2.0 using the softdevice S120 on an evaluation kit, but I am getting an error at the pstorage_init() function...
I'm trying to emulate an nRF24L01+ SPI slave interface with an nRF51822. The nRF24L01+ interprets the first byte in the SPI transfer as a "command", and the data that it will...
Hello,
we experience the situation, where we are able to flash a softdevice (s210) once. After the softdevice is flushed, subsequent attempts to flash the softdevice fail...
I was looking at the product brief for the nRF51922 - which states the SoC can handle both BT BLE and ANT concurrently. The product brief states:
Pin-compatible hardware...
Hello,
I have problem with two nRF24l01+
First is connected with a mcu to a sensor.
Second is connected with a mcu to a pc throught usb.
I want to get data from...
I'm looking to be able to plug my usb dongle into my computer and communicate with an application for users to use. In this communication, I would want to see the different...
Hi,
I would like to extend ..\nrf6310\s110\ble_app_beacon example and add the possibility of switching from beacon mode to configuration mode and then add a few services...
Hi,
I'm currently trying to use the PWM Library in the LED Button Example, I was able to get the LED to blink with the PWM library when USE_WITH_SOFTDEVICE=0, but ofcourse...
Hi all,
I am using sdk 5.2.0 and s110 softdevice 6.0.0 on PCA10006 and nRF6310 platform for development.
I encounter unpredictable BLE link loss issue. In my application...
