Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hello, I am trying to get a custom board with an nRF5340 (on a Raytac module) up and running. I want to emulate a simple HID mouse. Therefore, I selected the code from the...
I have just started using 2.7.0 with the nrf54L15 chips and come across a few problems.
When trying to run the UART sample I found that the app overlay files, which I believe...
Other than setting the DCDC_MODE_PIN, what else does the sd_power_dcdc_mode_set() do?
I'm seeing an issue where I have a GPS peripheral on UART that is seeing about 10dB...
Hi Nordic team,
Hi Nordic Team,
We are trying to configure two SPI masters. It works when I use any single SPI (only one), but when I add the second SPI, I encounter...
Hi,
I am trying to compile an old project.
I am using SEGGER_Embedded_Studio_Nordic_v568_win_x64 with nRF5_SDK_17.0.2
I am getting an error message for the following...
Does the 7002 support 802.11 monitor mode? https://en.wikipedia.org/wiki/Monitor_mode
Some chips call it promiscuous mode even though that should be something separate ...
First of all, I see that NRF52840 doesn't have a Real Time Clock but it has a Real Time Counter which is not working in case of sleep and low power mode, am I correct?
Second...
Hey everyone,
I am having trouble setting up the lsm6dsv16x as a interrupt. I was able to successfully poll the data meaning I can talk and read imu data, but no interrupt...
Hi , I wanna keep my existing mobile application which talks to nRF5340 over the BLE NUS service. I am using the default BT_UUID_NUS_VAL as my primary mode of communication...
I want to edit the explom firmware that comes with thingy91 to add the reading of new sensors and send them to nrf cloud. Where can I get the example of the Asset Tracker...
I have a custom board that started life based off of RF9160-DK 1.1.0.
We have a single programming header that can be used to program either the 52840 or the 9160 depending...
I've installed nRF Connect for VS Code Extension Pack v2024.9.5 to ubuntu 22.04 and after opening vscode the free disk space continues to diminish and cpu load is constantly...
Hello,
We are working on an integration between a nRF52832 and ST LIS3DH accelerometer on our custom board, using SDK 15.2.0 with SoftDevice and BLE enabled, and have observed...
The last couple of months I have been following the course “nRF Connect SDK Fundamentals”, but I am unable to get further than Exercise 2. This is because Visual Studio cannot...
