When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi
I am working on a BLE project and it requires some specific functionalities. I am not sure if all of them are doable. I have some questions about these. So, if someone...
Hi
After Google's Nest 2th Hub firmware update on December 17, 2022 and Google Home app update to support Matter1.0,
is there any case where the Nordic Thread module was...
I'm working on a project that uses the Fanstel BC840m module. The project uses a custom PCB design, and everything was going smoothly until... I enabled DCDC1, stopped building...
Hi,
I am comparing Asset Tracker v2 in SDK v2.2.0 and v.2.1.1
One of the changes is the newlib-nano C library in v2.2.0. CONFIG_NEWLIB_LIBC_NANO is set to "y" in v2.2...
Hello,
My customer's project is Asset tracker.
Here is scenario.
1. set #XSYSTEMMODE=1,1,1,3 (enable LTE-M and NB-IOT to connect nRF Cloud, enable GNSS, LTE preference...
I start using 2.2.0 SDK and had this error when building zephyr samples external_lib using nrf52833dk_nrf52833.
the problem as show in image:
after some research I found...
Im working with ncs 2.1.2 and trying to build MCUboot
Im trying to follow this instructions( link ) but I get the next log error when I try to build.
What am I doing...
Hi,
i want to receive extended advertising packets with a python script (for external testing). The pc-ble-driver-py approach looks really promising. And i tested the examples...
Good Morning
After successfully completed a multi link BLE + WS2812 on the nrf52840DK to nrf52840 dongle (on SDK5) I though I would try the exact same project on nrf Connect...
Hi!
Anomaly [199] states this workaround:
*(volatile uint32_t *)0x40027C1C = 0x00000082; Is it ok to set it once in the initialization and therefore mermanently or is...
Hi,
this is somewhat of a "meta" question:
I was looking at the different diagnostics clusters and what info / events they provide since these would be useful for a manufacturer...
Hello!
I am trying to monitor the GPIO pull-up drive capability of a microprocessor using a PPK2 module in "Ampere meter" mode.
PPK2 VIN is connected to the GPIO pin and...
Target nRF52832(nrf52dk_nrf52832) SDK NCS v2.0.0 Hello. We are preparing new project with nrf52832. It works as beacon (not connectable) I want nrf52832 have own BT mac address...
