Has anyone experience of successful TICK_DV calibration for nRF9E5? What order of accuracy should be achievable?
In my application I maintain a software RTC clocked by...
Hello,
I manage to work with new S310 V2.
I use S310 for hrm only. Saying so also not for DFU service.
I have own proprietary method for transfering application images...
I am working on an application and need to get the exact time that the master node receive advertising from the slave node. I tried with PPI and it's ok to capture the Radio...
Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
I seemed to be randomly causing problems to our nRF52840 Zephyr v2.02 sensor's flash.
Previously I had bricked 3 sensors somehow. Before full production, I need to know...
Hello,
I want to implement a vendor-specific service on the nRF5340.
Is there any suitable sample code in NCS 2.2.0?
Or if there is any documentation I should refer...
Hi,
I have a nrf52820 on a pcb without 32Mhz crystal. I am using nrf52833DK to flash the nrf52820 on the pcb using debug out port on DK. I am able to see the connected device...
Hi, it's me, once again. Thankfully the last problem I had was actually my fault... I got distracted and didn't notice a small implementation detail... anyway... Here's today...
Hi,
The customer test routine serial_lte_modem mqtt returns 9,0
What does this state mean?
* ``9`` - Ping response from the MQTT broker.
Thank you for all your...
Hi,
I'm getting the following error during migration from 2.0.0 to 2.1.0:
[505/551] Building CXX object CMakeFiles/app.dir/C_/ncs/v2.1.0/modules/lib/matter/src/app/util...
Hi all.
I'm trying to learn a bit more about the device overlays,
I'd like to know how I would access the "gpio-line-names" that I've specified in my overlay in my application...
Hello guys,
I'm trying to interface nrf52832 with ds18b20 temperature sensor and I'm using this code https://github.com/sigurdnev/Nordic-DS18B20 and I'm getting the output...
Hello,
I am currently having my product, which is based on the nrf52810 SOC, tested and certified. I have been told to set my device up to use the DTM firmware example in...
Hello everyone
I have a few questions about how the nrf chip works: - does nrf52 work by sending AT comman and we need an intermediate chip like pca10040 send AT command...
I am trying to modify the Zigbee light switch example to transmit commands to the first bound endpoint, rather than to a bulb address determined by the app logic:
ZB_ZCL_ON_OFF_SEND_REQ...
Hi,
I am testing GPIOTE interrupts on 833, and noticed the interrupt is not fired sometimes (randomly) on power up. The input level did change as measured but the interrupt...
In this commit https://github.com/nrfconnect/sdk-zephyr/commit/d4023b3c1b8c32d978299143125ce5543c9bc6bb and this conflicting commit https://github.com/nrfconnect/sdk-zephyr...
Hello,
I am trying to compile the zephyr/samples/subsys/display/lvgl.
I have the lv_conf.h enabled
I'm getting an error "No SOURCES given to Zephyr library: drivers_display...
