Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
Hello, I have managed to get two NRF5340s linked and measured their throughput. Now I need to change their Output Radio Amplifier Power to test again. And then I also need...
Hi,
I need to enable the ADC read and GPIO pin toggling to happen simultaneously at high precision, without using the MCU resources, approximately 15 us interval. After...
We have a device that is using the nrf_drv_csense module to measure a capacitive touch via the event_handler passed to nrf_drv_csense_init(). Unfortunately, due to various...
The latest versions of MbedTLS seem to have some level of support for TLS 1.3 that the nRF Connect library's MbedTLS version lacks. How can I use a newer version of MbedTLS...
Hello,
I am trying to use Eigen matrix library in a project on the nrf52832.
I was able to compile a very simple example however I get a mem_manage_fault while debugging...
I am trying to connect a low power camera Himax HM0360 to nRF52840 dk. In the camera device specification, it is mentioned that it provides I2C serial interface and full speed...
Hi, I'm just experimenting with my nRF9160 DK and have run into some questions regarding the default asset_tracker_v2 program and how some of it works. I have read the documentation...
Hi!
Basically, what it says in the title.
Datasheet mentions that for 2Mbps mode (enhanced shock burst) spacing should be 2Mhz or more.
Does that mean that number of...
Hello everyone,
I used nRF24L01 and Arduino to jamming 3 channel advertising BLE ( https://github.com/lws803/BLE-jammer ) and my Gateway can't receive message from my door...
I am trying to develop an environment based on the prx ESB sample and add nrfx_timer.h dependencies. This is not necessarily a question specific to this setup but a more general...
Hi,
I am using SDK 17 version. The file name is ble_app_uart_pca10040 . I send to data from nRF Connect app to nRF52 DK and this data reach correctly to nRF52. But i didn...
Hi,
Now I have some custom data that I want to save in flash to ensure data not lost when power off. What should I do?
Platform: Windows 10
NCS version: 1.9.1
Boards...
Currently, I'm facing a problem, that a custom board somewhat doesn't work. The main only consists of
The problem is, that the cpu seems to wake up every (about) 500us...
