I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
I am trying to upgrade from nRF Connect SDK v1.6.1, running under Ubuntu 18.04 using the Nordic Edition of SEGGER Embedded Studio as the Integrated Development Environment...
Hi, this is my setup:
nRF52840 Dongle configured to run as a peripheral BAS.
The BLE desktop app was used to configure the dongle.
I know that the dongle is working...
I was wondering how one might get the nRF9160 to enter the low power modes when making my own firmware? If possible could someone point me in the direction of an implementation...
We are building a gadget which senses temperature and humidity level using nrf5340 and using i2c as interface. We are using a slave which has SHT3X sensor for reading the...
I've been trying to use the NVS subsystem along with BLE and FOTA.
I got BLE and NVS working fine.
But if I enable FOTA (just including the code, not running an update...
I'm having trouble with a computer that can't run a Python script, which is using the library pc_ble_driver_py
I'm confused about the answer posted in
I've tried downloading...
Hi!
For a custom project, I need to enable and disable soft device for power consumption optimization. I've followed ble_app_gzll to enable and disable soft device. Unfortunately...
Hello,
I'm using the nRF52840 DK, SDK 17.1.0 and SoftDevice S140. My project is based on the Blinky peripheral example. The problem is the following:
Basically, turning...
I see a lot of threads about how you need to disable the UART while you're not using it because it has a couple of milliamps power consumption.
However, most of those threads...
Hello Team,
We are in process of designing our product with nRF52833. To secure our product and possible Firmware readouts, we are planning to use the APPROTECT feature...
So, I'm working on a project with two RGB LEDs, that's going to be powered by a coin cell. The device is going to spend most of it's time asleep, only waking up for a minute...
Hello - The nRF Connect for VS Code extensions updated today and it appears to have broken then nRF Terminal connection monitoring.
Old Behavior
Connect to device...
Hi,
I have a nRF52840-DK which comes with an o n-board SEGGER J-Link debugger/programmer to use with the internal microcontroller or an external one.
Also, I bought a...
Hello Sir/Madam,
I'm using Nrf52833 for ble_uart + saadc but this device given only 2 meter distance range .I want to increase that distance range.
How to increase distance...
