I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello
I'm going to use J-link's virtual port to see the characters being printed.
I connected custom pcb to Vcc, Swdio, Swclk, Gnd pin and tx, rx pin of J-link.
And...
In our mesh application, we are trying to give all our devices the same network key. As we are planning to have in excess of 100,000 devices, the 2-byte unicast address is...
Hello,
I am developing thread network and i am building on top of mqttsn_sleepy_publisher example. But I have problem to enable RTT logging (UART not available) for thread...
Hi, We are using nRF52840 in our design. the pin p0.10 is marked as LOW-FREQUENCY I/O (up to 10Khz) according to your recommended usage. Our software is design to generate...
Hi,
I am trying to use the VL53L0x sensor with the NRF52DK. Someone has written a library but its based on c++.
(*Edited) The example provided in github works with SDK16...
I created an Android app based on your Nrf UART app ver 1.0, which works fine on Android 4.4 and 5.0, but not 6.0. On 6.0, it cannot find the ble device. But I downloaded...
Hi, I'm looking to develop a GPS tracker over LTE-M/NB-IOT using nRF9160. The user needs to be able to reach the device to check its location on demand (20s delay is OK)....
Hello all,
In the proccess of migrating from arduino to SES IDE to work with the nrf52832 SOC and coming accros some of the examples in the SDK I'm strugglling to understand...
Hi,
We are using Jlink and nrfjprog to program the nRF52832 flash via SWD interface. We have a combined hex file which is about 512k and takes about 12 seconds to flash...
I am debugging my applications transitions to SYSTEM_OFF and back again. I am connected to the debugger so I am presumably testing with "emulated system off" which is just...
Hi all,
I wrote a nice library for using an offboard SPI flash chip and am now trying to port it to our master code which runs on freertos.. I wrote the library starting...
hello ,i am using sdk16 with nrf52852 DK i can be able to get time using that nrf calendar example. Now i want to sync up the mobile time with Dk every time i connect with...
Hello, i'm developing some boards with nRF24L01, everything was going fine, i was able to write and read payloads back and forth using modules mounted on 4 different hardwares...
