Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hey, I am trying to incorporate an app timer using the app timer function already on the code in the central and peripheral examples of the SDK for the UART examples. Specifically...
Hi Nordic,
I have old NRF52832 product which is developed by SDK11.0. The bootloader start address was set to 0x79000. Now We want to upgrade the it firmware by using...
Hi,
i'm using BLE MESH 3.0 Light Switch Example code. i want to send Light on-Off command every 2 second Timer base instead of Button press.
i got an error below.
Hi,
I am trying to develop the interactive_pyaci serial interface so that it can restore itself once it has been closed.
To do so it would be useful, once the db is loaded...
Hi,
Current github repo of IOS-nRF-Toolbox doesn't support X-code 10.2. Is there an update coming or is there a work around so that we can build app for ble-uart application...
I have the following issue: We are using the nRF9160 to track moving objects. Accuracy is of no importance, but battery life is. We experience the GPS accuracy as high, but...
Hello,
we've created a custom board with nRF52840 chip. The problem is that the device will not try to reconnect in a loop as it does normally in the examples. The function...
I am trying to get JLinkRTTClient (v646h) working on Ubuntu running in a VirtualBox 6.0 VM on Windows 10 host. I am using nRF52840 DK v1.1.0. I followed the guidance here...
Im using PCA10040 nrf52832 to measure light intensity with photodiode,
im using SAADC and SPI example to measure values but im not able to see any changes on UART as light...
We use the app button library to detect a change in position of three switches with the following configuration.
If the following sequence of events occurs,
1. Press...
Hello Nordic DevZone,
While trying to recover nrf52832 chip using command nrfjprog -f nrf52 --recover, I received the following error: Recovering device. This operation...
Hi ,
The following problem is happening in my case with old android devices. I found your answer from other thread.
"The phone first sends a LL_VERSION_IND and then it...
Now I use sdk15.2.0 hrs project to add the spim.
the mode of the spi is timer+ppi+spi.
question:1.I can't enter the led_timer_handler on time;2.I can't get the right data...
Dear All,
I am trying to use the external crystal as the source clock of the softdevice, as well as of the rtc. I am not sure if all this is possible and because I am...
Hello, I am trying to use PWM in the simple coap client example. Unfortunately the PWM is not working, I do not get any signal on the output pins. If I remove the line with...
