Hi,
I'm trying out S130 SoftDevice. I have 1 device with S110v7 which acts as a peripheral.
2nd device contains S130 0.9 (I've based my code on S120 multilink central example...
I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
Dear all,
I am trying to adopt the flash_fds example to fit my needs. What I initially need to get sorted out is how can I erase the memory pages after I have fully written...
hi, team.
I've got a question. I use nrf52840 dev board. There is a connection between nrf52840 and ds18b20. I tried to use dedicated HW timer to count delay according to...
Hi team,
There is connection between nrf52840 and ds18b20. I have made simple lib for ds18b20. When i get temerature without softdevice (s140) all works correct (use 9-bit...
Howdy,
I'm trying to access the SD card on my device via the usb MSC and am not sure the best way to proceed.
I have a custom board with an nrf52840, and it works great...
Hi,
I would like to make development on nRF52840-DK by using Segger Studio.
However, I could not find detailed document that specifies how I should start development...
Hello all
I was just following the thread launched by Alex concerning nrf 52 dongle driven from serial port, which is also very important to me, and now that thread is already...
Hi,
i would like to program my module nRF52840 via uart.
I generated private then public key using nrfutil.exe tool
i could programm softdevice and bootloader and...
I am trying to get the DCDC running on my custom NRF51822 board.
It is running but the results are a bit disappointing.
If I do a test and enable the TX with and without...
I've picked up a nRF52840 DK and dongle to do some testing with long-range beacons.
So far I think I have managed to configure my DK as a beacon in long-range mode (can...
Hi
I have a test mesh network, with several devices provisioned using nRF Mesh and.... a proxy node which has been provisioned using an alternative method but with the same...
Hi, I'm trying to make a SIG qualification Project. QDID97989 (nRF52 S132 V5.0.0) with replace PHY QDID97482(TaiyoYuden module). Launch Studio Project type is "qualification...
How to send and receive messages in ble mesh? The sending and receiving of sensor data I have done is not a switch value. I have tried many methods but failed.
I alredy run the assert tracking about 4 months ago on preliminary firmware.
Now I updated the modem firmware to v1.0.0 and compiled the last stable AT Client project from...
In the past we had a C based product that communicated from our Host processor over SPI to an nrf8001 peripheral using an Application Controller Interface (ACI) provided as...
