Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi,
I try to program hex file with openOCD. The flash part is written without any problem. OpenOcd only fail to write the UICR registers beyond 0x10001200.
However it...
Hello,
Which one of the following statements regarding " sd_ble_gap_connect " function call is true:
(1) Can sd_ble_gap_connect function put the central device into initiating...
static void pdm_event_handler(nrf_drv_pdm_evt_t const * const evt) { /* Process the events. */ }
/* ... */
/* Process the events. */
Can you make a little more detail...
Hello,
I have NRF5230 DK board and I have powered the board with external battery. Solder bridge SB12 is shorted and I have cut the jumper SB29 and disabled power for Interface...
I am trying to connect nrf52832 ble module to esp32/esp8266 application mcu connected with SPI interface.
I use ble_central/ble_app_hrs_c application, but found that the...
Hi Sir,
we use 52832 ESB , one PTX and two PRX. (PRX_A and PRX_B)
A and B have same base_addr_0 and base_addr_1 .
diffrent addr_prefix
PTX send package to A and wait...
I am trouble with adding DFU function to BLE_UART on nRF52832. I have just followed those step in this link Adding DFU to your App . But when i compile and fash to my device...
Hi all, My company is doing a proyect with BLE. We use nRF51822 with the softdevice s130. I am preparing the FCC and CE certification. Our tester asked us to prepare 2 samples...
hi, nordic team:
Now I am using the nRF5 AirFuel SDK version 2.2.0 to develop the PTU and successfully use the serial to do the dfu function.
I used nrfutil for DFU, but...
Hello, I trying to debug with GDB server Because of this .
I open the GDB server like this
go to build directory and write client cmds below
output is $4 = {<error...
SDK12.30 supports S132 V3.0. Is there any other version SDK supporting S132 v3.1?
Any problem for firmware built with S132 V3.0 and running on module with S132 v3.1?
Hello,
I've disabled the buttons in light_switch example for the client DK. I'm using GPIOs for input and I want to enable BSP_BUTTON_3 to reset mesh network configurations...
After switching to SDK 15 from SDK 14, stopped working correctly transmission of HID Report Descriptor over USB, what in case leads to incorrect device enumeration.
Now...
I'm developing a database with FDS that stores application-level data that must be able to be matched to bond data. After looking at the files for Peer Manager, ID Manager...
Hi All,
What is the recommended way to choose FIFO and buffer sizes for the nrf_serial module? I mean the optimal values for the following constants:
SERIAL_FIFO_TX_SIZE...
