Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi team, I am using nrf52 sdk 14, nrfjprog version: 9.7.3 and JLinkARM.dll version: 6.14c,getting this issue while flashing:
ERROR: JLinkARM DLL reported an error. Try again...
Hi all,
I have a functional FW, which is running properly 99 % of the time. But sometimes I have some RESET with RESETREAS register set to SREQ, but I'm not able to find...
Hello,
I am completely new to creating a Bluetooth mesh network and nRF5 devices. I have three nRF51 DK and 2 nRF51 dongles. I have earlier read the posts and made nRF51...
I am working in sdk15 nrf52832 ble_app_hids_keyboard.
I want merge ble_app_uart_c ,so modify in
sdk_config.h :
NRF_SDH_BLE_CENTRAL_LINK_COUNT 1
PM_CENTRAL_ENABLED...
Please check the Device above its nRF52832 based device.
I want to program Softdevice and app using nrfjprog from my PC // or by using nRFStudio
is it possible ?
Hi,
Which version of softdevice do I need to use in order to get support for ble_gap_scan_params_t?
I am tring to build a central applicaiton, are there any code examples...
We have been trying to create a binding library for Xamarin based on the DFU library at: https://github.com/NordicSemiconductor/IOS-Pods-DFU-Library
So, far, we were able...
There's an if statement in `ble_advertising_init` around setting the scan response data which never evaluates false:
The comparison of `&p_init->sr_data != NULL` will...
Found the same problem:
https://devzone.nordicsemi.com/f/nordic-q-a/34160/light_switch-example-sdk-v2-0-1----problem-with-server
1) The server does not receive the address...
Hello. Complete n00b here!
I've built a small sample on mbed of an I2c Scanner. Also tried other runtimes. Somehow, its not working.
I'm using a GY-45 Module, which wraps...
Hi there
I tried to observe the message when DTM are working.
So I modify the example direct_test_mode to display on monitor.
But after modified , it comes out the error...
The nRF5 SDK references a field ble_adv_legacy_enabled in the ble_adv_config_modes_t structure (see http://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter...
nrf52832.
SDK14.2
Segger ES V3.34a
I am using sd_ble_gatts_value_get, in C file named ble_cus.c to retrieve the 'value' of a characteristic as written to by the...
Recently i am developing an application based on UART on nRF51822 platfrom, where an application receives the data through UART. During development, i went through nRF UART...
