Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hi all !!!
I understand Output OOB, Input OOB.
I case of No OOB, value which is attached to Confirmation value is 0x00, what happens in case of static OOB?
Hi there~~ I'm trying to create a voice streaming application with the Mesh and the Nordic Thingy:52 I downloaded both the nRF5 SDK 14.2 & Mesk v1.0 to test the Mesh's light_switch...
Hi everyone,
Currently, my team is developing a BLE keyboard which uses 6KRO protocol. Are there any examples for the 6KRO protocol using nRF52 chips?
Thanks!
Update:
Hi again to everyone!
After a while, I've received a new custom board and a new cable to connect through P19. But everything are not working again.
Now, in...
I have a 12 MHz voltage controlled oscillator driving the nRF9E5 at pin xc1 and xc2 is open will this pose a problem for running the nRF9E5? The clock has a +-50ppm stability...
I am working on a project that requires me to wirelessly communicate with and program a left hand Oculus Touch controller, since dismantling it will cause damage. The controller...
I see I have more than 100 free pages (~ 101 KB) on Nrf51822 with SD130 but how can I assign all of them to the FDS module. I am going to manage a database with FDS on the...
Hello,
I am trying to use PCA10000 dongle with the pb-ble-driver-py libraries with absolutely no success, as I get a "Failed to open. Error code: 13" error.
I am running...
Hi, please!
The question is related to "nRF24L01P_Product_Specification_1_0.pdf" datasheet in " www.nordicsemi.com/.../nRF24L01P_Product_Specification_1_0.pdf" and to NRF24L01P...
Hello. Engineers.
I'm a beginner in nRF52832, I'm looking for someone who can help me.
I have nRF52832 development kit. I tried examples blankly with SDK14.0.
It working...
Hi,
I've recently come across a problem where in some cases my device's memory gets trashed.
Ideally I'd be able to set a watchpoint on a memory location so that I could...
main.c
I am working in sdk14.1 nrf52832 ble_app_uart_pca10040_s132 and ble_app_uart_c_pca10040_s132.
ble_app_uart_pca10040_s132:
nrf_ble_gatt_att_mtu_periph_set(&m_gatt...
Hi,
I'm using nRF52810 on SDKv14.2 and I have changed the bootloader from 52832 to work for 52810. I could do OTA now. I found that the bootloader there is no timeout when...
We are developing a test jig that also programs the Nordic nRF51822 on our board.
We are receiving the following error message from the command line programmer:
NRFJPROG...
