Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
I have an application where I need to synchronize several devices to within 1us using a radio. In order to do this, we need to make a protocol that allows precise synchronization...
We have these Dev Kit Nrf52 and also Nrf51 Bluetooth Smart Beacon Kit. For our application and for the simplest user experience we would like to benefit from update via OTA...
My product only offer a debug interface（SWDIO/REST，SWDCLK，+3.3v，GND），but I learn that the nRF51 DK debug out interface has several pins，such as EXT VTG，EXT GND DETECT，EXT...
hi all:
I am a new user.Now i have a project in which I need to implement a function a host and four devices .I just want to know if i use the example of " gzp_dynamic_pairing...
Is a delay needed between Characteristic updates
I modified the ble_sdk_app_proximity example.
I added x3 services, based on the BLE Characteristics, a beginner's tutorial...
I have 32-bit float numbers, sent to the BLE from SPI.
I can manipulate this into x4 bytes, or actually use sprintf and get a real 6-byte representation of the number.
...
I have taken ble_app_ancs_c_s130_pca10028 example and modified the application to run on our custom board.
The custom board uses NRF51822 (NRF51 IC revision 3).
The following...
Hi,
We are using nRF51822_QFAB (128K/16K), S110 V8.0.0 and SDK V10.0.0 for my development. We are in the need of guest (unbonded), pairing and bonded mode.
Guest...
Hello,
I'm struggling with setting up the eclipse IDE to build the blincky program in the SDK now I've configured all the paths and eclipse configuration according to this...
Hi ,
I am using nrf5 SDK v12.2.0 ,
I have an nrf51822 board .. can I just compile the examples in SDK for pca10031 and use it for nrf51822 . Please let me know what I...
Is it possible to have two nRF52 devices connected in such a way to send UART data in a bi-directional way.
Would device 1 be a BLE central and the other BLE peripheral...
I followed the link: infocenter.nordicsemi.com/index.jsp to build and load the app into two boards.
Step 1 ~ 8 are working as expected. But
Step 9 "Observe that LED...
Dear Nordic,
What I want to do:
Battery powered sensor network
One gateway (BLE --> WLAN) with a serial-to-wifi chip connected to nRF52
MQTT (IBM Bluemix -...
Hi there,
I'm in the middle of migrating an application from SDK 10 to SDK 11. In the SDK 10 version, I had RTT logging working just fine. I'm developing on a Mac so I...
