Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Launch an example for UART (BLE PERIPHERAL) on the board PCA10040. When try to set the parameter APP_ADV_TIMEOUT_IN_SECONDS = 0 (no timeout) get returned NRF_ERROR_INVALID_PARAM...
Hello,
I have a question regarding AVDD pin.
I am using nRF51822 CEAA package. And the reference circuitry on the datasheet uses a 1.0nF capacitor between VDD and GND...
Hi everyone
I'm facing a weird problem in my design and FreeRTOS. Apparently, my system was working fine, but along I'm adding more tasks, i've detected the system stops...
I'm using RS485 driver on NRF51822 uart. I started software developing with ble_uart exapmle.
RS485 as always has direction control inputs.
Before data transfer to uart...
In my app I have the following:
s110
20 ms min connection interval
100 ms max connection interval
4000 ms con_sup_timeout
I'd like to set the slave_latency...
Hi,
The documentation states -96dBm rx sensitivity for 1mbit BLE mode and -93dBm for proprietary 1mbit mode.
Is it possible to use BLE mode (3 in MODE register) but...
I want to scan for peripheral devices in central-role and at the same time i want to broadcast in peripheral-role. How do i have to initialize the Softdevice in this case...
Hi,
I'm originally iOS app developer.
I have been developing with custom PCB that based on nRF51 chip. (not nordic development kit)
My PCB has a gyro sensor and some...
Hi,
Whenever i m trying to upgrade my application using iphone with binary file then i get "unsupported DFU" error. what is meaning of this error and how can i resolve...
Hi please help,
We are facing a problem of Gazell failure (not getting interrupt on gazell ISR) when i perform external Flash write using SPI.
If i disable gazell and...
hello there i downloaded nrf5 iot sdk. i have nrf51 and nrf52 kit.now it has many example codes like tcp,udp. can anyone tell me how to test it with my kits??
Hi everybody
Can nrf51822 advertise with a Balun whose SE pin is disconnected? (not connected to antenna, just left disconnected)
Just like the reference circuitry above...
Hello,
I can see, that sd_ble_gatts_hvx() returns 13313, if the notification is not enabled for that characteristic from the connected central. --> S120 Softdevice runs...
Hi
I got my new NRF51 DK. I was able to test it with blinky using mbed. I had to add the add the device nRF51-DK. then compile it and drag the .hex file into the mbed drive...
