i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
application note nAN-034 describes two alternatives for production testing an application using the nRF51822. One method is using a commercial tester (MT8852) and the other...
I need to send data PIR motion detector sensor to the master controller in my motion detector network.
Can I get away with just one of the nrf51 chips and my PIR sensor...
We're trying to decide at what voltage we should run our nRF51822 on the next revision of our board. To date we've been doing fine at 1.8V. The current drawn on a 3.7V lithium...
hi, i made ble app including bootloader using nRF51822 (s110), sdk 6.1.0
when i use sd_nvic_SystemReset() function in app, it erase app's pstorage.
But i want to preserve...
Hi,
I use S120 as central device and I need to handle multiple connections.
However S120 works quite unclear to me.
If S120 doesn't reply to BLE_GAP_EVT_CONN_PARAM_UPDATE_REQUEST...
Hello ,
I am trying to develop an application using the S130 soft device using Keil MDK v5 Lite. I have came to know that it is not possible to generate a code size greater...
I've run into a problem using the provided spi master code.
I get the following error message from Keil
spi_master.c(381): error: #1059-D: an entity with an internal...
Hi
I want to run the ble_proximity template on micro blend (Readbear lab). But I can't make it to work. I have uploaded the code to the board and using the nRF Proximity...
Hi all, I have followed the steps described
https://devzone.nordicsemi.com/question/14780/nrf51822-development-kit-without-nrfgo-starter-kit/
with the alternative power...
Hi,
I have successfully implemented a HID keyboard, using the nRF8001 and arduino sdk 0.9.1 ported to a microchip PIC18F controller. Connecting to iPhone iOS7.1.2
Everything...
hello,
please find main.c file of code and how to add the MAC address to the ble_app_hrs sample code
that was provided in the samples directory of the SDK.
Can you...
hi,
I am trying to develop a network of ble devices.i want nrf51822 to function as a master and slave( not necessarily simultaneous). For that i need to develop a custom...
Hello,
Firstly, I just begun with BLE and I am trying to program nrf51822 to read the sensor data through TWI (I2C) connection and send this reading to the central device...
I have tested the ble_app_proximity sample firmware on nRF51822 eval kit and also on my custom board.
Everything, regarding the used services seems to work as intended. However...
We have an application in which it would be nice to change the supply voltage for our Nordic module (nRF51822 running the Soft Device) depending on which other modules on...
