Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
I'm using the nrf5340_audio application and with SDK 2.6.0. The Bluetooth address printed out in the terminal does not match what actually shows in advertisements. For example...
Hello,
I work on a board with nRF9160 and nRF52840. I can perform firmware update of both application and mcuboot for nRF52840 (using serial recovery mode) from the nRF9160...
Hi, I'm having problems with migrating my project to SDK v2.9.0. I'm using mcuboot and I want to use b0n on the net core and update support for the net core application via...
Hello,
In BLE service whether can I use same Characteristics UUID ( Ex : using 0x2A6E / Temperature or 0x2A1C / Temperature measurement) with only difference in the description...
We're using nrf52833 and our target board is already running our program well.
Then
we'd like to flash by using Jlink SWD programmer.
So, we connected vref, gnd, swdio...
We have found a nrf52833 DK (PCA101000) with id, 685888541 with 2024.4.
So, it might be used as previous project in our company.
Anyway, I tried to test with this DK board...
based on SDK v2.9.0
1 Central, 4 Peripherals, Repeat the following:
Power off 3 Peripherals, wait a while, power on 3 Peripherals.
The following error usually occurs...
Hello.
I am trying to run an alarm clock using the RTC calendar. In the main loop I see the time being printed, but there is no response from the alarm callback, which I...
Hi,
in my case I need to flash the nRF5340DK board with only a standalone merged_domains.hex , which I get from another co-worker, no source code. how to do it?
Best...
Hi.
I wanna evaluate nRF52840-DK. However, when I tried to install Toolchain on Visual Studio Code, a message "Failed to fetch available toolchains." is displayed. "nRF...
Greetings to everyone.
We have the nRF52840-DK, where the Power Switch SW8 physically is broken.
Is there any way (a bypass, making a bridge/shortcut, using a soldering...
HI everybody,
I have problem with my Nordic nrf9151-DK. I am not able to use GNSS with this kit. A looked at documentation and found, that i have to activate XCOEX0...
Hi,
I have been using the nRF52840 for a long time, and everything was working fine. However, now LED5 starts blinking whenever the USB is connected to J2. I have tried...
Hello, I am new to using the nRF platform, and I appreciate your understanding. I am currently using SDK 2.8.0.
I have implemented a thread in the application core to acquire...
