Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
I have nrf9160 custom board, and I have issue with SIM module. I'm not getting 1.8 volt in "SIM_1V8" pin.
- I download the latest version from nRF Connect SDK v2.2.0 from...
Hello,
I am trying to setup a device ( Semtech LR1110 ) connected to SPI 1 peripheral on the nRF5340pdk .
I have a driver code for it. My question is this.
How can...
Hi,
Happy New Year!
I have been going over LwM2M location assistance documentation , and cannot figure out whether LwM2M library handles the response automatically, or...
I'm using Asset Tracker V2
with the Settings Enabled and tsetting up an external littlefs storage area.
I want to use the shell built in command "fs" to write stuff to...
I have two i2c modules on the same bus and I plan to have a common timer for both of these. one of these is a sensor and I only want to read the sensor values at a predefined...
Hi I am using the Zephyr code base after trying to update the ncs to 2.1.2 from 1.9.2 I notice that the function "flash_area_open" is returning a -2 error as it couldn't find...
Hi,
I am using nrf mesh sdk v5.0.0 and am using sensor server model example to build our own application on top of it. SOC we are using is nRF52832. I have enabled the...
Hi,
I have few doubts regarding the internal flash of nRF52810. I am not using SoftDevice. I am using SDK 17.1.0
I would like to write around 20 bytes to internal flash...
board : nrf5340 sdk : nrf-connect v2.1.2
Hi. I am studying OpenAmp and RPMSG using NRF5340DK board.
I looked at the examples below for studing OpenAmp and RPMSG.
C...
nRF Connect SDK 2.2.0 on Windows 10 pro, I have a nrf52840-DK and a nrf9160-DK. I would like to test a simple OpenThread CLI application
I have the following prj.conf
...
Hi, team.
I am trying to find a way to write some persistent data in factory.
The data is a couple of certificates and should be written differently for each devices....
I am a beginner, and there is no problem with scanning and receiving data in RTT Viewer. I am currently stuck on how to use CDC ACM US. i have notice there are example on...
I am interfacing with a part that uses the same pin, P0.6, for two purposes:
1) The pin is used for UART communication. MCU RX input.
2) The pin is used as a GPIO. MCU...
Hi Everyone,
I have a custom board with a nRF9160. I have updated the firmware to 1.3.3. I am using SDK 1.9.1. I found that the board works well with the GNSS sample from...
