I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
In nRF51 SDK 7.1.0, there is a c header file using c++ keywords operator .
Here is a snippet of components/ble/ble_racp/ble_racp.h using the keywords.
/**@brief Record...
Hello, I have several development-related questions about the microphone functionality of the NRF5340 AUDIO DK in headset mode:
Is it possible to configure the device...
I saw in this video that there was a lipo battery being used with a nrf52 Development Kit and I read this in the spec for the nrf5340 Development kit:
1.7-5.0 V supply...
Hi,
I am connecting a central to multiple peripherals. In order to optimize the throughput I would like to simultanuously sniff the connection. In the nrf Sniffer documentation...
We are producing an issue where the ZBOSS stack will emit a ZBOSS Fatal Error without any context if we alter ZB_DEV_REJOIN_TIMEOUT_MS. Specifically, the steps to reproduce...
Hello! I am trying to get gazell to work on the nrf52840 dongle.
I built the nrf connect sdk Blinky project with the nrf52840 dongle set as the config. then pushed the merged...
In the past, we've been able to use the nRF52-DK to flash our boards, supplying power through the debug port by shorting SB32.
For our L15 prototypes, the nRF52-DK doesn...
Hello Team,
I am experiencing an issue with the sound output from an external codec connected to the nRF5340 DK. Currently, the sound is in mono, but my goal is to achieve...
Hello,
I recently purchased a few NRF9161-DK boards for both LTE and NR+ evaluation. However, I am unable to run through the initial demo. The board is discoverable initially...
NCS 2.7, nrf52840, sysbuild with mcuboot, multiple board revisions
I have setup my build to use different keys for each board revision with this in my sysbuild.conf:
...
Hello DevZone,
I just located a mysterious bug , it's about printk() and low power.
Environment:
NCS v2.8.0 and v2.9.0
nRF52840DK v3.0.2
PC: Ubuntu 22.04
Zephyr...
Hello. I am attempting to run the Matter Template app sample on the Adafruit Feather nRF52840 Express board.
I created a pm_static.yml file with the following configuration...
Hi,
I am using nrf52840 with nrfSDK-16.0, Ble5 coded PHY( S=8 ). I am using ESP32S3 as central and nrf52840 as peripheral device. I want to connect to 8 peripherals with...
When I try to program the Thingy:91 in cellular mode, it always gives the message 'Failed to connect to port.' I’ve tried different ports, but I get the same result.
When using the nrf Connect Extension for VS Code, the nRF Connect SDK v2.9.0 and the "at_client Sample" application, flashing the nRF9160 and an actinius icarus board using...
