I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
HI
I am trying filter peripheral devices based on UUID while scanning. I have set, enabled the scan filters but still output is displaying all the peripheral devices irrespective...
Hi I am using nrf52832 board and SDK15.2 I have below requirement:
Nordic board should act as central as soon as it gets booted and scan for particular service if present...
Hi, I have modified the twi_scanner example of the 52840 DK to be compatible with nRFDongle.
I fully erased the dongle with Segger and passed the new hex file with SWD cable...
I found this very useful Throughput Measurement Application for for Threads: http://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.thread_zigbee.v2.0.0...
HI, I have a custom service with customs characteristics and I need the maximum speed posible.
I have one service for write without response and another service only with...
Hi,
We implement oob pairing using NFC.
According to my knowledge NFC is used as "private" advertising channel (this is what OOB means) i.e. peripheral address, encryption...
Hi,
I have created a custom Serivice and custom characteristics in the attached application
Please find the attached application which create a custom Characteristic with...
hi nordic,
i had a nrf52 dk where it should only advertise to specific device like my phone with nrf connect app and that nrf52 dk should not advertise to other devices...
Hi,
My name is Bruno and I'm developing an Application which consists on:
Connect to a BLE device (I'm using Nina B112 from u-blox, which contains a NRF52832 SoC) through...
So I have successfully built & deployed the Light Switch Demo - and it works.
But where do we go next?
The documentation seems far too close-in focussed on the microscopic...
Hi,
what is the typical or max wake up time of the nRF52 from the RTC or GPIOTE irq (when configured as sense for low level input)?
In my setup, I see a wakeup time...
Hi,
can I use a pin with A/D converter (or comparator) and at the same time read its logic value using GPIO and configure it to be event source in PPI?
Thanks
I have develop a project on nRF52832 and I want to migrate to nRF52840.
I am able to build pre-devloped project from directory nRF5_SDK_14.2.0_17b948a/example/tasol/ble_app_template...
We have used nRF24L01s in our most recent project but would like to switch to the nRF52832, while still using the Enhanced Shockburst radio protocol.
We are prototyping...
Hi,
We are looking at the nRF52840 and would like to have 5 such devices in their own piconet, 1 Central device and 4 Peripherals, with a 2 Mbit PHY,
and want to achieve...
