Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
When i choosing among the 52832 and 52840, i found this table.
One point i am not sure, i believe the 52832 stack is already support Bluetooth 5, but why the table said...
Hello,
I would like to manage time (hours, minutes, seconds) on NRF52 chip: what is the best way to do it ? How to use as less energy as possible ?
At the first connection...
Hi all,
I'm new to Bluetooth technology and just start some test for indoor localization using 52382. But I find out that 52382 does not support the long range feature of...
Hello all,
I'm curious if anyone could lend some thoughts.
I'm just in the research stage and going through a few examples but getting a little overwhelmed.
I'm trying...
Hi,
I am using nRF51822, S130, SDK 12.3.0
Want to use is low power failure warning. using the following code.
However, when break on line err_code = sd_power_pof_enable...
I am currently using a CSR 4.0 dongle 8510 A10 chip on Windows 10 Creators update
I can get it to Pair with the nRF52832 in windows, according to windows.
I have a ...
I am upgrading an existing project that was working on SDK 14.2.0 with S132 5.1.0 to SDK 15.0.0 with S132 6.0.0. I'm using IAR 8.20.1, and have made the changes suggested...
Hi,
My aim is to transmit the beacons. iam using nrf51822 usb dongle and nRF5_SDK_12.1.0).I need to run E:\nrf1\examples\ble_peripheral\ble_app_beacon\pca10028\s130\arm5_no_packs...
Hi All!
I use SPI with ss_pin = NRF_DRV_SPI_PIN_NOT_USED. but seems it doesn not work properly.
in the file nrfx_spi.c , the following code exist to init ss_pin during...
Hello,
I am using a nrf51422 in my work. I am focusing on reducing system power consumption as much as possible.
Q. When a peripheral (server) starts advertising (and...
I am about to develop a Bluetooth Mesh network with the nRF52832.
With the PCA10040, i already able to form a Bluetooth Mesh Network, such that there is one client act...
Does anyone know where I can find a list of which phones/tablets support Data Length Extension (DLE)?
We are finding that many budget phones (e.g. Motorola G6, Samsung Galaxy...
Hi,
I'm using nRF52840 (rev 1.0.0) and Mesh 2.0.1 and SD 15.0.0.
I added FreeRTOS following the example "hrs FreeRTOS".
In FreeRTOS, the source clock (configTICK_SOURCE...
Hi,
I'm trying to use RTC2 as a custom timer using the RTC Driver, initialised as :
nrf_drv_rtc_t erx_timer_rtc = NRF_DRV_RTC_INSTANCE(2);
But when the BSP library or...
Good morning everyone,
I read a lot of threads in the last week on this subject, but so far I was not able to find a solution to the problem.
On a custom board we are...
