I am working on BLE. I have created a service using read property(services_set_barometer_service_barometer_data(void *src, int size))
After connection is set-up i am calling...
Hello, I'm using the nRF51822 and tried the HID Keyboard Application (S110, ble_app_hids_keyboard) example. (Nordic\nrf51822\Board\nrf6310\ble\ble_app_hids_keyboard )
The...
Hi all,
I have a situation in which softdevice (s310 v2) seems not to forward events to my nrf app (bootloader running dfu) in spite of the fact that my iOS app sees the...
I am sending setup commands to a NRF8001 D device and I receive a command response with status of 0x89. This appears to respond to ACI_STATUS_ERROR_UNSUPPORTED_FORMAT. I cannot...
Hi I'm working on a school project and I need to send data from an accelerometer to a phone I'm currently able to update "dummy" data from my nrf51822 to my phone after following...
Working on an ANT project.
Switched a project from S210 to S310 to add BLE feature.
For the ANT part, there is no source code modification at all.
Sweet.
This is not...
Has anyone experience of successful TICK_DV calibration for nRF9E5? What order of accuracy should be achievable?
In my application I maintain a software RTC clocked by...
Hi
sir we have nrf9160-dk and planning to interface some sensors to it but the issue we are facing is that the gpios are at 1.8v where as we need 3.3v logics to interface...
Hello everyone,
I getting stocked now for 1,5 days to get the nRF-Connected SDK running
I am using macOSCatalina 10.15.7
segger 5.20
Nordic SDK Tag v1.4.0
using...
Hi Team,
I'm working on scanner and NCS/Zephyr bt_le_scan_start callback API
typedef void bt_le_scan_cb_t(const bt_addr_le_t *addr, int8_t rssi, uint8_t adv_type, struct...
Hi
I have implemented a custom DFU process, where NRF52840 sends another NRF52833 an image to program.
The NRF52833 receives the image and validates CRC, if all OK , I...
Hi,
I'm using a nrf52833 in may application.
I have 2 Identical units with bare nrf52833.
refer the unit as normal ad defective.
test a.
while flash a simple FW...
Hello ,
I am using NRF 52 DK 15.3.0 SDK and ble_free_rtos_hrs example , I want to have a feature to start and stop the advertisement ( by interrupt driven , task notify...
Hi Nordic..
currently we are going to implement serial bootloader dfu from other MCU (infineon chip).
We have create flasher from MCU to nrf52832 to do serial fw update...
Hi
I am using nrf52832 .i am trying to connect to a device using sd_ble_gap_connect but i am getting NRF_ERROR_INVALID_ADDR error.
i am modifying ble_app_cli to achieve...
Hello
I'm going to use J-link's virtual port to see the characters being printed.
I connected custom pcb to Vcc, Swdio, Swclk, Gnd pin and tx, rx pin of J-link.
And...
In our mesh application, we are trying to give all our devices the same network key. As we are planning to have in excess of 100,000 devices, the 2-byte unicast address is...
Hello,
I am developing thread network and i am building on top of mqttsn_sleepy_publisher example. But I have problem to enable RTT logging (UART not available) for thread...
Hi, We are using nRF52840 in our design. the pin p0.10 is marked as LOW-FREQUENCY I/O (up to 10Khz) according to your recommended usage. Our software is design to generate...
