I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
In nRF51 SDK 7.1.0, there is a c header file using c++ keywords operator .
Here is a snippet of components/ble/ble_racp/ble_racp.h using the keywords.
/**@brief Record...
Hi,
I have a problem in my application, i want to add scanning feature, but
When i call sd_ble_gap_scan_start () with these parameters it returns error (0x06) (with...
I am a begineer in Nordic trying to read voltage and current readings from ADC pin. I need to read both values in parallel, with known interval. So I need to use interrupts...
I am trying to use the LTE Sensor Gateway app to send Running Speed and Cadence Service Sample Application data loaded on a nRF52832. I have managed to get this two device...
Hi,
I have a problem with timer and nrfx. I use the migration guide:
So I r emove the old configuration entries related to the nrf_drv_* drivers from my sdk_config.h...
Hello,
I am currently using nRF52832 with SDK v11.0.0 and S132 v2.0.0. I am also using the soft device as my application requires. I have been trying to put the CPU into...
Hello, When i try to use nrf9160 with the BME280 sensor over I2C i get this error
***** USAGE FAULT ***** Illegal use of the EPSR ***** Hardware exception ***** Current...
Hello,
I am using BLE+MCU MBN52832 module and i am facing one issue while programming my application.
I am uploading the hex file using nrfGo Studio and when i try...
I have a custom nRF52840 board that I am implementing the Open Bootloader (from SDK 15.3). Push Button/Power control is handled by the STM6601 device. It keeps the power ON...
When I open a new project in SES and paste the code of blinky led example from " \nRF5_SDK_15.3.0_59ac345\examples\peripheral\blinky\pca10040\s132\ses ", and start compiling...
Hi. every one
First of all, i am a beginner.
I connected the max44009 and CJMCU2080 sensors to the board.
and also get a value.
but sgp30 sensor is faile
there...
HI. i use SEGGER Studio and SDK 15.3.0.
I usally use printf func for debug. however as use SDK func, I need to use NRF_LOG_INFO casue SDK file use NRF_LOG_INFO for debuing...
Hi,
I am trying to port an existing project to a Mesh SDK example. Some files include the math.h library and use the round function. During the build process I am getting...
Hi I use nrf-ble-driver ver.4.1.1 with PCA10031 dongle (nRF51844 chip on board) and "connectivity_4.1.1_1m_with_s130_2.0.1.hex" firmware for that dongle. in this case ATT_MTU...
Hello to everyone. I´m starting to work with Mesh configuration in nRF52 SDK. I was testing the "light_switch" example as client and server in Mesh v3.10, provisioning with...
